Ir para o conteúdo principal

Conserte seus objetos

Direito de executar reparos

Peças e ferramentas

Introdução

The display assembly includes the LCD, digitizer and frame. You may need to transfer some components from your original display. Used assemblies may be missing one or more of the elastic grommets shown in the new assemblies.

  1. Pry with a plastic opening tool, or your fingernail, in the divot to the left of the rear-facing camera, near the power button. Lift the rear case by the corner nearest the divot and remove it from the phone.
    • Pry with a plastic opening tool, or your fingernail, in the divot to the left of the rear-facing camera, near the power button.

    • Lift the rear case by the corner nearest the divot and remove it from the phone.

  2. Use a plastic opening tool, or your fingernail, to press the microSD card slightly deeper into its slot until you hear a click.
    • Use a plastic opening tool, or your fingernail, to press the microSD card slightly deeper into its slot until you hear a click.

    • After the click, release the card and it will pop out of its slot.

    • Remove the microSD card.

  3. Insert a plastic opening tool, or your finger, into the notch of the battery compartment and lift the battery upward to remove it.
    • Insert a plastic opening tool, or your finger, into the notch of the battery compartment and lift the battery upward to remove it.

  4. Use a plastic opening tool, or your fingernail, to press the SIM card slightly deeper into its slot until you hear a click.
    • Use a plastic opening tool, or your fingernail, to press the SIM card slightly deeper into its slot until you hear a click.

    • After the click, release the card and it will pop out of its slot.

    • Remove the SIM card.

  5. Kit de ferramentas básico para eletrônica

    Kit pequeno. Grandes possibilidades.

    Shop Toolkits

    Kit de ferramentas
    básico para
    eletrônica

    Shop Toolkits
  6. Use the tip of a spudger to remove the four metallic pads located in each corner of the device.
    • Use the tip of a spudger to remove the four metallic pads located in each corner of the device.

    • Using a Phillips #00 screwdriver, remove the 12 screws connecting the midframe to the device.

  7. Use the plastic opening tool to pry around the entire edge of the midframe now to release it from the front case.
    • Use the plastic opening tool to pry around the entire edge of the midframe now to release it from the front case.

  8. Use the flat end of a plastic opening tool to disconnect the USB board connector. Disconnect the front-facing camera cable connector. Disconnect the earpiece speaker assembly cable connector.
    • Use the flat end of a plastic opening tool to disconnect the USB board connector.

    • Disconnect the front-facing camera cable connector.

    • Disconnect the earpiece speaker assembly cable connector.

    • Disconnect the headphone jack assembly cable connector.

    • Disconnect the display/digitizer cable connector.

    • Disconnect the antenna cable connector.

  9. Remove the single 2.4 mm Phillips #00 screw from the motherboard assembly.
    • Remove the single 2.4 mm Phillips #00 screw from the motherboard assembly.

  10. Remove the motherboard.
    • Remove the motherboard.

  11. Disconnect the daughterboard connector from the frame. Slowly peel off the daughterboard and remove it from the device. Slowly peel off the daughterboard and remove it from the device.
    • Disconnect the daughterboard connector from the frame.

    • Slowly peel off the daughterboard and remove it from the device.

Conclusão

To reassemble your device, follow these instructions in reverse order.

5 outras pessoas concluíram este guia.

Justin Ogihara

Membro desde: 18-09-2017

8.568 Reputação

20 Guias de autoria

Equipe

iFixit Membro de iFixit

Community

114 Membros

11.095 Guias de autoria

Adicione um comentário

Exibir estatísticas:

Últimas 24 horas: 0

Últimos 7 dias: 6

Últimos 30 dias: 31

Duração total: 1,167