Pular para o conteúdo principal

Introdução

Broken volume button? Use this guide to remove the volume button on your Galaxy Note 5. The guide will take you through the steps of removing the back glass, separating the middle housing and removing the necessary parts to remove the volume button.

  1. Insert a SIM Ejector Tool into the small hole on the left side of the top edge of the device.
    • Insert a SIM Ejector Tool into the small hole on the left side of the top edge of the device.

    • Press down until the SIM Card Tray begins to protrude out of the device.

  2. Remove the SIM Card Tray from the slot.
    • Remove the SIM Card Tray from the slot.

  3. Heat the back of the device with a heat gun for 2 minutes
    • Heat the back of the device with a heat gun for 2 minutes

  4. Once the device is heated, place a suction cup near the bottom of the back of the device Make sure it is placed on the flat part of the glass
    • Once the device is heated, place a suction cup near the bottom of the back of the device Make sure it is placed on the flat part of the glass

    • Be careful holding the device after heating the back, it may burn!

    • Gently pull upwards on the suction cup to separate the rear glass from the body of the phone.

    • While pulling upwards, insert a pick under the rear glass

  5. Keeping the pick under the rear glass, move the pick along the bottom edge of the device to cut the adhesive.
    • Keeping the pick under the rear glass, move the pick along the bottom edge of the device to cut the adhesive.

  6. Repeat the previous heating and cutting procedure for the remaining three sides of the phone.
    • Repeat the previous heating and cutting procedure for the remaining three sides of the phone.

    • Leave a pick on each side as you continue to the next to prevent the adhesive from resealing.

  7. Once all adhesive has been cut, gently lift up the rear glass to remove it.
    • Once all adhesive has been cut, gently lift up the rear glass to remove it.

  8. Remove the S-Pen from the bottom of the device
    • Remove the S-Pen from the bottom of the device

  9. Remove 20 5mm screws with a Phillips #1 Screwdriver. Remove 20 5mm screws with a Phillips #1 Screwdriver.
    • Remove 20 5mm screws with a Phillips #1 Screwdriver.

  10. Grip the back of the device and press down on the white square to remove the middle housing. Grip the back of the device and press down on the white square to remove the middle housing.
    • Grip the back of the device and press down on the white square to remove the middle housing.

  11. Loosen the power button flex adhesive by holding it with the tweezers. With the tweezers, pry up and remove the power button flex
    • Loosen the power button flex adhesive by holding it with the tweezers.

    • With the tweezers, pry up and remove the power button flex

  12. Push out the power button with the tip of the tweezers.
    • Push out the power button with the tip of the tweezers.

  13. Loosen the volume flex adhesive. Pry up and remove the volume button flex.
    • Loosen the volume flex adhesive.

    • Pry up and remove the volume button flex.

  14. Push out the volume button and remove it from the device.
    • Push out the volume button and remove it from the device.

Conclusão

To reassemble your device, follow these instructions in reverse order.

Uma outra pessoa concluiu este guia.

Bernice Nunez

Membro desde: 19-04-2018

295 reputação

2 Guias de autoria

Equipe

Cal Poly, Team S25-G17, Maness Spring 2018 Membro de Cal Poly, Team S25-G17, Maness Spring 2018

CPSU-MANESS-S18S25G17

4 Membros

5 Guias de autoria

Adicionar comentário

Visualizar Estatísticas:

Últimas 24 horas: 0

Últimos 7 dias: 3

Últimos 30 dias: 24

Todo: 511