Introdução

Use this guide to replace the front panel display assembly in your Samsung Galaxy Note.

Grasp the cap of the stylus and remove it from its slot in the midframe.
  • Grasp the cap of the stylus and remove it from its slot in the midframe.

Adicionar comentário

Pry with a plastic opening tool, or your fingernail, in the divot to the right of the rear-facing camera, near the volume rocker.
  • Pry with a plastic opening tool, or your fingernail, in the divot to the right of the rear-facing camera, near the volume rocker.

Adicionar comentário

  • Lift and remove the rear case from the phone.

Adicionar comentário

  • Insert your finger in the notch of the battery compartment.

  • Press the battery toward the rear facing camera while pulling outward.

Adicionar comentário

  • Use the flat end of a spudger, or your fingernail, to press the microSD card slightly deeper into its slot until you hear a click.

  • After the click, release the card and it will pop out of its slot.

  • For reassembly, push the microSD card into the slot until it clicks in place.

Adicionar comentário

  • Remove the microSD card from its slot in the midframe.

Adicionar comentário

  • Use a plastic opening tool, or your fingernail, to push the SIM card out of its compartment.

Adicionar comentário

  • Slide the SIM card out the rest of the way with your thumb and remove it from the device.

Adicionar comentário

  • Remove the nine 3.4 mm Phillips #00 screws securing the midframe to the display assembly.

Adicionar comentário

  • Insert your plastic opening tool to the left of the power button between the midframe and the front panel assembly and pry.

Adicionar comentário

  • Slide the plastic opening tool down the seam.

Adicionar comentário

  • Insert your plastic opening tool to the left of the headphone jack between the midframe and the display assembly.

  • Slide the opening tool along the top edge of the phone.

  • Continue to run the plastic opening tool around the perimeter of the phone until the midframe is separated.

Adicionar comentário

  • Remove the midframe from the display assembly.

Adicionar comentário

  • Use the flat end of a spudger to carefully disconnect the display cable connector.

Adicionar comentário

  • Use a spudger to disconnect the front-facing camera assembly cable connector.

  • Disconnect the headphone jack/earpiece speaker assembly cable connector.

  • Disconnect the digitizer cable connector.

Adicionar comentário

  • Disconnect the soft button cable connector with the flat end of a spudger.

  • Use a spudger to disconnect the USB board cable connector.

  • Disconnect the antenna cable connector.

Adicionar comentário

  • Remove the two 3.4 mm Phillips #00 screws securing the motherboard to the display assembly.

Adicionar comentário

  • Remove the motherboard assembly from the display assembly.

Adicionar comentário

  • Remove the two 3 mm Phillips #00 screws securing the upper display assembly bracket.

Adicionar comentário

  • Use a pair of tweezers, or your fingers, to remove the upper display assembly bracket.

Adicionar comentário

  • Using tweezers, or your fingers, remove the front-facing camera assembly.

Adicionar comentário

  • Use the tip of a spudger to pry the headphone jack/earpiece speaker assembly out of its recess in the display assembly.

Adicionar comentário

  • Use tweezers, or your fingers, to remove the headphone jack/earpiece speaker assembly.

Adicionar comentário

  • Remove the three 3 mm Phillips #00 screws securing the speaker enclosure to the front panel assembly.

Adicionar comentário

  • Lift the speaker enclosure from the display assembly.

Adicionar comentário

  • Use the tip of a spudger to disconnect the antenna cable connector from the USB board.

  • Remove the antenna cable.

Adicionar comentário

  • Push the flat end of a spudger under the USB board to separate it from the display assembly.

  • Insert the spudger at a shallow angle to avoid bending or damaging the USB board.

Adicionar comentário

  • Remove the USB board.

Adicionar comentário

  • Insert the tip of a spudger under the vibrator connector cable near the contacts then slide toward the vibrator itself.

Adicionar comentário

  • Insert the flat end of a spudger under the vibrator connector cable, and pry it up from the adhesive.

Adicionar comentário

  • Remove the vibrator from the display assembly.

Adicionar comentário

Conclusão

To reassemble your device, follow these instructions in reverse order.

36 outras pessoas concluíram este guia.

Sam Lionheart

Member since: 18-10-2012

337.397 reputação

535 Guides authored

Equipe

iFixit Membro de iFixit

Community

112 Membros

6.721 Guides authored

étape 31 ensuite ??

Fabrice - Responder

i have a galaxy not and its display is badly broken,at the top of the phone(front side),the display is broken so badly that i am able to a little circuit i.e. a brown color wire which is connected to the display.

so my ques. is that can the phone work after repairing or it has gone?

Abhishek Kumbhar - Responder

Hello Abhishek Kumbhar, if the motherboard is not damaged it's all fine. All other parts are replaceable

Georg Fischer - Responder

excellent photos

of samsung 717

murali maroju - Responder

i am trying to get my phone to charge but its not and i have it pluged in and it doesnt want to charge

Anthany Kleven - Responder

Adicionar comentário

Visualizar Estatísticas:

Últimas 24 horas: 4

Últimos 7 dias: 24

Últimos 30 dias: 118

Todo: 41,804