Conserte seus objetos Comunidade Loja

SG 552-1 Commando Barrel Replacement

Introdução

This guide will be showing step-by-step instructions on how to get to and replace the barrel of the airsoft gun.

O que você precisa

  1. SG 552-1 Commando Barrel Replacement, Barrel: passo 1, imagem 1 %32 SG 552-1 Commando Barrel Replacement, Barrel: passo 1, imagem 2 %32

    • Using a flathead screwdriver, remove the pin holding the hand guard in place.

    • To remove this, turn the pin clockwise and push it through at the same time.

    • Pull the hand guard off.

    Editar

  2. SG 552-1 Commando Barrel Replacement: passo 2, imagem 1 %32 SG 552-1 Commando Barrel Replacement: passo 2, imagem 2 %32

    • Using a Phillips #1 screwdriver, remove the two 8mm screws above the hand guard on both sides of the gun. There should be four total.

    Editar

  3. SG 552-1 Commando Barrel Replacement: passo 3, imagem 1 %32 SG 552-1 Commando Barrel Replacement: passo 3, imagem 2 %32

    • Locate the button to fold over the folding stock and fold over the folding stock.

    • Using a Phillips #1 screwdriver, remove the 20mm screw located behind the folding stock.

    Editar

  5. SG 552-1 Commando Barrel Replacement: passo 4, imagem 1 %32 SG 552-1 Commando Barrel Replacement: passo 4, imagem 2 %32

    • Turn the gun over so that you are facing the bottom of the gun.

    • Using a Phillips #1 screwdriver, remove the following screws:

    • Remove the 8mm screw located directly underneath the cocking lever.

    • Remove the 8mm screw beside the one you just removed.

    Editar

  6. SG 552-1 Commando Barrel Replacement: passo 5, imagem 1 %32 SG 552-1 Commando Barrel Replacement: passo 5, imagem 2 %32

    • Carefully tug on the tip of the gun and pull the barrel and its cover out.

    Editar

  7. SG 552-1 Commando Barrel Replacement: passo 6, imagem 1 %32 SG 552-1 Commando Barrel Replacement: passo 6, imagem 2 %32 SG 552-1 Commando Barrel Replacement: passo 6, imagem 3 %32

    • Pull the barrel out from the cover.

    • Remove the pieces at the end of the barrel.

    Editar

  8. SG 552-1 Commando Barrel Replacement: passo 7, imagem 1 %32 SG 552-1 Commando Barrel Replacement: passo 7, imagem 2 %32

    • Remove the remaining pieces of on the ends of the barrel.

    Editar
Conclusão

To reassemble your device, follow these instructions in reverse order.

Autor(a)

com 5 outros contribuidores

Laura Schulz

Membro desde: 10/05/12

1 Reputação

Autoria de 1 guia

Emblemas: 1

Equipe

Cal Poly, Team 18-41, Regan Fall 2012 Membro de Cal Poly, Team 18-41, Regan Fall 2012

CPSU-REGAN-F12S18G41

Membros da 6

Autoria de 6 guias

0 comentários

Adicione um comentário

Exibir estatísticas:

Últimas 24 horas: 0

Últimos 7 dias: 0

Últimos 30 dias: 2

Duração total: 1,642