Conserte seus objetos Comunidade Loja

Replacing VTech MobiGo Touch Learning System Speaker

Introdução

This page is for disassembling the speaker inside the device. Before following these steps, please refer to the Disassembling VTech MobiGo Touch Learning System Case Guide first.

O que você precisa

  1. Replacing VTech MobiGo Touch Learning System Speaker, Case: passo 1, imagem 1 %32

    • Remove the battery covers and the four batteries.

    Editar

  2. Replacing VTech MobiGo Touch Learning System Speaker: passo 2, imagem 1 %32 Replacing VTech MobiGo Touch Learning System Speaker: passo 2, imagem 2 %32

    • Remove the four plastic caps with a metal spudger to expose the 6.0 mm Philips JIS #0 case screws.

    • Remove the eight 6.0 mm JIS #0 case screws.

    Editar

  3. Replacing VTech MobiGo Touch Learning System Speaker: passo 3, imagem 1 %32 Replacing VTech MobiGo Touch Learning System Speaker: passo 3, imagem 2 %32

    • Using a plastic opening tool, separate the two pieces of the case carefully.

    Editar

  5. Replacing VTech MobiGo Touch Learning System Speaker, Speaker: passo 4, imagem 1 %32 Replacing VTech MobiGo Touch Learning System Speaker, Speaker: passo 4, imagem 2 %32

    • The speaker will be attached to the back of the case.

    • Unscrew the two 6.0 mm Philips J0 screws.

    • Careful! The wires are still attached to the back of the case and to the speakers.

    Editar

  6. Replacing VTech MobiGo Touch Learning System Speaker: passo 5, imagem 1 %32 Replacing VTech MobiGo Touch Learning System Speaker: passo 5, imagem 2 %32

    • Lift the round speaker with a plastic opening tool.

    • Remove the two wires connected to the speaker.

    • You can use wire cutters or regular needle nose pliers to disconnect the wires from the speaker.

    • Once the wires are disconnected, remove the speaker from the back of the case.

    Editar

  7. Replacing VTech MobiGo Touch Learning System Speaker: passo 6, imagem 1 %32 Replacing VTech MobiGo Touch Learning System Speaker: passo 6, imagem 2 %32

    • Solder the wires to the appropriate spots on the new speaker, making sure that both wires are properly connected.

    • The wires may be hot.

    Editar

  8. Replacing VTech MobiGo Touch Learning System Speaker: passo 7, imagem 1 %32 Replacing VTech MobiGo Touch Learning System Speaker: passo 7, imagem 2 %32

    • Insert the new speaker into the hatch located in the middle part of the panel using a plastic spudger.

    • Make sure the speaker is the right size for the panel.

    • Once the speaker is properly placed, screw in the two 6.0 mm Philips J0 screws.

    • Do not over tighten the screws or the panel will break.

    Editar
Conclusão

To reassemble your case, follow the case instructions in reverse order.

Autor(a)

com 3 outros contribuidores

RBansil

Membro desde: 08/27/15

221 Reputação

Autoria de 2 guias

Emblemas: 6

+3 outros emblemas

Equipe

USF Tampa, Team 8-3, Eyestone Fall 2015 Membro de USF Tampa, Team 8-3, Eyestone Fall 2015

USFT-EYESTONE-F15S8G3

Membros da 3

Autoria de 17 guias

0 comentários

Adicione um comentário

Exibir estatísticas:

Últimas 24 horas: 0

Últimos 7 dias: 1

Últimos 30 dias: 6

Duração total: 1,365