Conserte seus objetos

Direito de executar reparos

Loja

Removing Playstation 2 Slimline SCPH-7500x Outer Shell

Escrito Por: Jared Hirata (e 20 outros contribuidores)
  • Comentários: 2
  • Favoritos: 8
  • Execuções: 7

Dificuldade

Fácil

Passos

7

Tempo necessário

5 minutos

Partes

1

Sinalizadores

1

In Progress

Em progresso

Este guia está em progresso. Atualize para acompanhar as últimas mudanças!

Introdução

This guide will walk you through step-by-step on how to properly remove and replace the outer shell in the PlayStation 2 Slimline.

Ferramentas

Comprar estas ferramentas

Peças

Nenhum componente especificado.

    • Turn off the PlayStation 2 and carefully unplug it from the power source. Also, it is important to eject the CD from the console before flipping the it upside down.

    Editar

  2. Locate the six feet on the bottom of the PS2.

    • Locate the six feet on the bottom of the PS2.

    • Five of these feet are in plain sight while the last foot is located under the black void sticker on the back of the device.

    • Some versions of the console, such as the PAL Version, may not have this sticker. In this case, the foot or the screw should be in plain sight.

    Editar

  3. Remove the five visible feet from the bottom of the device using a spudger. Remove the five visible feet from the bottom of the device using a spudger. Remove the five visible feet from the bottom of the device using a spudger.

    • Remove the five visible feet from the bottom of the device using a spudger.

    Editar

  5. Remove the sticker and then remove the 6th foot. Remove the sticker and then remove the 6th foot.

    • Remove the sticker and then remove the 6th foot.

    Editar

  6. After all of the feet have been removed, Use a Phillips #1 screwdriver to remove the six 4.0mm screws from the base of the PS2. After all of the feet have been removed, Use a Phillips #1 screwdriver to remove the six 4.0mm screws from the base of the PS2. After all of the feet have been removed, Use a Phillips #1 screwdriver to remove the six 4.0mm screws from the base of the PS2.

    • After all of the feet have been removed, Use a Phillips #1 screwdriver to remove the six 4.0mm screws from the base of the PS2.

    Editar

  7. Once all of the screws have been removed, pry apart the plastic covers. Start by lifting the side containing the power cable and Ethernet port. Then, lift the opposite side to fully separate the two sides. You may need to apply some gentle force to detach the covers. Be careful not to break the plastic screw pins. You may need to apply some gentle force to detach the covers. Be careful not to break the plastic screw pins.

    • Once all of the screws have been removed, pry apart the plastic covers. Start by lifting the side containing the power cable and Ethernet port. Then, lift the opposite side to fully separate the two sides.

    • You may need to apply some gentle force to detach the covers. Be careful not to break the plastic screw pins.

    Editar

  8. If done correctly, you should have a fully detached plastic backing, revealing the electronic components of the PlayStation 2.

    • If done correctly, you should have a fully detached plastic backing, revealing the electronic components of the PlayStation 2.

    Editar
Conclusão

To reassemble your device, follow these instructions in reverse order.

7 outras pessoas concluíram este guia.

Autor(a)

com 20 outros contribuidores

Jared Hirata

Membro desde: 09/04/2013

600 Reputação

7 Guias de autoria

Emblemas: 12

+9 outros emblemas

Equipe

Cal Poly, Team 17-4, Regan Spring 2013 Membro de Cal Poly, Team 17-4, Regan Spring 2013

CPSU-REGAN-S13S17G4

3 Membros

14 Guias de autoria

0 comentários

Adicionar um comentário

Adicione um comentário

Exibir estatísticas:

Últimas 24 horas: 0

Últimos 7 dias: 0

Últimos 30 dias: 21

Duração total: 2,405