Introdução

The function of a XLR cable is to carry a balanced audio signal. It connects in the bottom of the microphone to the XLR microphone connector.

  1. Make sure you have a proper three pin XLR cable.
    • Make sure you have a proper three pin XLR cable.

    • Grab the female end of the cable (plug with three holes).

    Adicionar comentário

  2. Line up the pins in the end of the microphone (microphone connecter) with the holes in the XLR cable.
    • Line up the pins in the end of the microphone (microphone connecter) with the holes in the XLR cable.

    Adicionar comentário

    • Once the pins are aligned, push the cable into the bottom end of the microphone. You should hear a click.

    Adicionar comentário

Conclusão

To disconnect the cable from the microphone, follow the instructions in reverse.

12 outras pessoas concluíram este guia.

nat coll

Member since: 27-09-2012

372 reputação

14 Guides authored

Equipe

Cal Poly, Team 7-53, Forte Fall 2012 Membro de Cal Poly, Team 7-53, Forte Fall 2012

CPSU-FORTE-F12S7G53

5 Membros

18 Guides authored

When disconnecting the cable - press the little latch (pointing towards you in the last picture) to release and then pull the cable out.

harrywwc - Responder

Is this April's fool? XD

s6963172 - Responder

how i repair the PG48 the XLR conector moves in and out when the cable ar plugged. The conector male in the microphone have an screw but that one not works...

What am i do?

If you have an idea to the answer or any tip to resolve this trouble feel fre to tweet me.

@ Theradioholic

on

#Twitter

Santiago Morales - Responder

I know a few people who would see this and still screw it up.

jimboc - Responder

do it in reverse? you have to press the button though on the male end...

Michael Fox - Responder

Will this work with an Audio-Technica ATM-410, or just the Shure?

cbrislain - Responder

Just Shure. On Audio-Technica you have to rotate the plug six times clockwise and whisper a few nice words into it before plugging it in. I've always found that lullabies work quite well.

staale -

I have a 1/4 adapter on my Shure, is that process different? I can't seem to make the male 1/4" connect to the female XLR

JON CAMPBELL - Responder

Push harder.

staale -

Some of us are musicians , so we appreciate the help

tomandlindafirme - Responder

When do you hear the sound from it?

Charlie Green - Responder

Bloomin' eck.... & I've been using cellotape, Blu Tak and super glue. No wonder I had to revert to the megaphone all the time

george sandoz - Responder

I don't know about you lando77 but I always blow on the female end (the cable end with the holes) to blow dry any moisture out. What good does it do to blow on the male pins?

darryltrimm - Responder

Do these instructions work for the ElectroVoice EV 635A as well?

carterjim - Responder

This is useless. Why didn't you post a video that shows the process.

mperloe - Responder

Wow!!! Thank you so much! This is really great information. Now I won't have to hire people to come do this for me anymore. Can you post a video of how to put the microphone on a stand?

dhoffman98 - Responder

Thanks for posting this, I recently ran out of toilet tissue and have been using my Shure SM58 Owner's Manual. You're a lifesaver!

hemightbefluffy - Responder

He's holding the plug with his right hand. But what if I'm left handed. Do I need to rotate it? Or should I switch what side I'm standing on?

Bob DeMaa - Responder

Managed it on 5th attempt , now what the heck do I do with the other end of the cable ???

gary blair - Responder

are these instructions specifically for drummers or can anybody use them?

Cedric the Dead - Responder

Adicionar comentário

Visualizar Estatísticas:

Últimas 24 horas: 1

Últimos 7 dias: 11

Últimos 30 dias: 55

Todo: 58,886