Conserte seus objetos

Direito de executar reparos

Peças e ferramentas

Este guia tem alterações mais recentes. Mudar para a última versão não verificada.

Philips DC320 37 Speaker Replacement

Escrito Por: Graham Rolph (e 6 outros contribuidores)
  • Comentários: 0
  • Favoritos: 0

Dificuldade

Fácil

Passos

8

Tempo necessário

20 minutos

Partes

2

Sinalizadores

1

Confusing Text

Texto confuso

Alguns dos textos deste guia é confuso, duplicado ou fora-tópico. Melhore-o!

Introdução

Follow the procedure outlined in this guide to remove and install a speaker.

  1. Pry off the four white feet with the pointed end of the spudger

    • Pry off the four white feet with the pointed end of the spudger

    Editar

  2. Unscrew the four 15.5 mm Phillips #2 screws that hold the bottom panel to the dock.

    • Unscrew the four 15.5 mm Phillips #2 screws that hold the bottom panel to the dock.

    Editar

  3. Use the flat end of the spudger to pry the lid off from the two connectors holding it to the body of the dock.

    • Use the flat end of the spudger to pry the lid off from the two connectors holding it to the body of the dock.

    • The connectors on the panel are fragile and may break.

    Editar

  4. Kits para o Nintendo Switch

    Um reparo rápido para reiniciar o jogo

    Confira kits para o Nintendo Switch

    Kits para o Nintendo Switch

    Um reparo rápido para reiniciar o jogo

    Confira kits para o Nintendo Switch

  5. Carefully pull up and out the four electrical connectors and the two ribbon connectors connecting the bottom panel and the dock. Electrical Connectors Ribbon Connectors

    • Carefully pull up and out the four electrical connectors and the two ribbon connectors connecting the bottom panel and the dock.

    • Electrical Connectors

    • Ribbon Connectors

    • The cables do not have a lot of slack in them. Be careful not to break the connectors.

    • One wire is soldered onto the bottom panel. Be careful not to break this bond.

    Editar

  6. Unscrew the two 6 mm Phillips #00 screws attaching the back panel to device.

    • Unscrew the two 6 mm Phillips #00 screws attaching the back panel to device.

    Editar

  7. Slide the back panel towards top of the device and lift away from the device to detach back panel. Slide the back panel towards top of the device and lift away from the device to detach back panel. Slide the back panel towards top of the device and lift away from the device to detach back panel.

    • Slide the back panel towards top of the device and lift away from the device to detach back panel.

    Editar

  8. Unscrew the four 16 mm Phillips #2 screws attaching the speaker unit to device.

    • Unscrew the four 16 mm Phillips #2 screws attaching the speaker unit to device.

    Editar

  9. Slide the speaker towards the bottom of the device to remove. Slide the speaker towards the bottom of the device to remove.

    • Slide the speaker towards the bottom of the device to remove.

    Editar
Conclusão

To reassemble your device, follow these instructions in reverse order.

Autor

com 6 outros contribuidores

Graham Rolph

Membro desde: 18/04/2013

1 Reputação

2 Guias de autoria

Emblemas: 2

Equipe

Cal Poly, Team 3-48, Amido Spring 2013 Membro de Cal Poly, Team 3-48, Amido Spring 2013

CPSU-AMIDO-S13S3G48

4 Membros

6 Guias de autoria

0 comentários

Adicionar um comentário

Adicione um comentário

Exibir estatísticas:

Últimas 24 horas: 0

Últimos 7 dias: 2

Últimos 30 dias: 9

Duração total: 712