Conserte seus objetos

Direito de executar reparos

Loja

Panasonic Lumix DMC-F7 Replacing LCD Screen Replacement

Escrito Por: Alex Penman (e 11 outros contribuidores)
  • Comentários: 0
  • Favoritos: 1
  • Execuções: 1

Dificuldade

Difícil

Passos

12

Tempo necessário

Sugerir um tempo??

Partes

3

Sinalizadores

5

Inconsistent Images

Imagens inconsistentes

Atualizar as imagens deste guia para ser mais consistente com os pré-requisitos aumentaria a sua grandiosidade.

Student In Progress

Estudante em progresso

Este guia está sendo trabalhado por alunos esforçados.

Grammar Police

Polícia gramatical

Abrace seu professor de Inglês interior e ajude a melhorar a gramática deste guia!

Action Shots

Fotos de ação

Seja um herói em ação! Este guia precisa de imagens que melhor demonstrem como executar ações específicas.

Confusing Text

Texto confuso

Alguns dos textos deste guia é confuso, duplicado ou fora-tópico. Melhore-o!

Introdução

If you’ve cracked the screen or are experiencing issues with the screen of your Panasonic Lumix DMC-F7 digital camera, it may be time for a replacement. To complete this replacement, you will need to know how to solder. You will also need a few tools, so be sure to check the Tools List below before starting this replacement. This guide will help you properly replace the LCD (liquid crystal display) screen for the Panasonic Lumix DMC-F7 digital camera.

  1. Slide the lock into the unlocked position to the right.

    • Slide the lock into the unlocked position to the right.

    • Use your finger to slide battery hatch towards the arrow sign.

    • Both battery and memory card should now be visible.

    Editar

  2. Open battery hatch and the black cover to expose the battery compartment.

    • Open battery hatch and the black cover to expose the battery compartment.

    • The camera used to create these repair guides did not have a battery and memory card.

    • Pull the battery out and replace with a new one.

    • When putting the battery back in, make sure it is in the same orientation as before.

    • Close the battery compartment and make sure the lock is in the locked position.

    Editar

  3. Remove the two 2.8 mm Phillips screws as shown in picture.

    • Remove the two 2.8 mm Phillips screws as shown in picture.

    Editar

  4. Use a Philips screwdriver to remove the three 2.8 mm Phillips screws on the bottom of the camera as shown in picture.

    • Use a Philips screwdriver to remove the three 2.8 mm Phillips screws on the bottom of the camera as shown in picture.

    Editar

  5. Remove the two 2.8 mm Phillips screws on the side of the camera as shown in picture.

    • Remove the two 2.8 mm Phillips screws on the side of the camera as shown in picture.

    Editar

  6. Use a spudger to pry open the case from all sides. Use a spudger to pry open the case from all sides.

    • Use a spudger to pry open the case from all sides.

    Editar

  7. Beware of the ribbon cable that is still attached when opening. Use your fingers to carefully pry off the back casing from the camera assembly.

    • Beware of the ribbon cable that is still attached when opening.

    • Use your fingers to carefully pry off the back casing from the camera assembly.

    Editar

  8. Lay the camera on its front side. Use the spudger to open the film strip locking mechanism and remove strip.

    • Lay the camera on its front side. Use the spudger to open the film strip locking mechanism and remove strip.

    • Hold down on the camera's metal casing with one hand. Use your other hand to completely lift the back case off the rest of the camera, making sure the film strip separates.

    Editar

  9. Use a spudger to lift the screen ZIF connector tab. Use the back of the spudger to push the ribbon cable free.

    • Use a spudger to lift the screen ZIF connector tab.

    • Use the back of the spudger to push the ribbon cable free.

    Editar

  10. Use the screwdriver to remove the four 2.4mm Phillips screws as shown in picture, circled in red. Lift up the LCD screen from the front case. Potential for device damage: The wire is still connected to the board in the other side.

    • Use the screwdriver to remove the four 2.4mm Phillips screws as shown in picture, circled in red.

    • Lift up the LCD screen from the front case.

    • Potential for device damage: The wire is still connected to the board in the other side.

    Editar

  11. Remove the LCD screen from its case.

    • Remove the LCD screen from its case.

    Editar

  12. Locate the wire connecting the LCD screen to the motherboard.

    • Locate the wire connecting the LCD screen to the motherboard.

    • Use the soldering iron to desolder the wire.

    • Use the soldering iron to solder wires from new LCD screen to the circuit board.

    Editar
Conclusão

To reassemble your device, follow these instructions in reverse order.

Uma outra pessoa concluiu este guia.

Autor

com 11 outros contribuidores

Alex Penman

Membro desde: 28/01/2011

463 Reputação

4 Guias de autoria

Emblemas: 9

+6 outros emblemas

Equipe

Cal Poly, Team 7-35, Regan Winter 2011 Membro de Cal Poly, Team 7-35, Regan Winter 2011

CPSU-REGAN-W11S7G35

4 Membros

10 Guias de autoria

0 comentários

Adicionar um comentário

Adicione um comentário

Exibir estatísticas:

Últimas 24 horas: 0

Últimos 7 dias: 14

Últimos 30 dias: 29

Duração total: 2,740