Menu

Suas configurações

Minha bancada de trabalho

Ganhe acesso rapidamente a guias, partes e respostas para seus dispositivos
Carrinho

Parece que seu carrinho de compras está vazio

Visite Nossa Loja

Palm Treo 650 Camera Replacement

Escrito Por: cgood (e 5 outros contribuidores)
  • Comentários: 0
  • Favoritos: 2

Dificuldade

Moderado

Passos

10

Tempo necessário

10 minutos

Seções

3

Sinalizadores

3

Grammar Police

Polícia gramatical

Abrace seu professor de Inglês interior e ajude a melhorar a gramática deste guia!

Inconsistent Images

Imagens inconsistentes

Atualizar as imagens deste guia para ser mais consistente com os pré-requisitos aumentaria a sua grandiosidade.

Incorrect Tools

Ferramentas incorretas

Ajude a fazer melhor este guia usando as ferramentas corretas em imagens e/ou texto.

Introdução

This guide will help you access and replace the Treo's camera if it is no longer functional.

Ferramentas

Comprar estas ferramentas

Peças

Nenhum componente especificado.

  1. Position the phone so the screen faces down.

    • Position the phone so the screen faces down.

    • Remove the stylus found on the back of the phone.

    Editar

  2. To remove the battery cover, hold down the button in the middle of the phone's back.

    • To remove the battery cover, hold down the button in the middle of the phone's back.

    • Slide the cover down to remove. Set the cover aside.

    Editar

  3. Lift the edge of the battery, separating contact points, and pull out as pictured. Lift the edge of the battery, separating contact points, and pull out as pictured.

    • Lift the edge of the battery, separating contact points, and pull out as pictured.

    Editar

  4. Remove the small round rubber cover on the back of the phone located immediately below the antenna.

    • Remove the small round rubber cover on the back of the phone located immediately below the antenna.

    • This will uncover a screw that will be removed in the next step.

    Editar

  6. Unscrew six black 6.9 mm Torx screws with a T5 Torx Screwdriver. Unscrew one 9.75 mm Phillips antenna screw with a Phillips #00 Screwdriver. Pull out the antenna.

    • Unscrew six black 6.9 mm Torx screws with a T5 Torx Screwdriver.

    • Unscrew one 9.75 mm Phillips antenna screw with a Phillips #00 Screwdriver.

    • Pull out the antenna.

    Editar

  7. Pry the back cover off using a spudger or similar tool. The back cover is attached by several small clips on the inside.

    • Pry the back cover off using a spudger or similar tool.

    • The back cover is attached by several small clips on the inside.

    Editar

  8. Remove the two 3.75 mm screws. Pull off the logic board. Pull off the logic board.

    • Remove the two 3.75 mm screws.

    • Pull off the logic board.

    Editar

  9. Pull the rubber ring off of the camera. Pull the rubber ring off of the camera. Pull the rubber ring off of the camera.

    • Pull the rubber ring off of the camera.

    Editar

  10. Pry off the metal camera case. Lift up the camera, but do not remove. The connector must be detatched first.

    • Pry off the metal camera case.

    • Lift up the camera, but do not remove. The connector must be detatched first.

    Editar

  11. Pry off the camera connector plug. Remove the camera.

    • Pry off the camera connector plug.

    • Remove the camera.

    Editar
Conclusão

To reassemble your device, follow these instructions in reverse order.

Autor

com 5 outros contribuidores

cgood

Membro desde: 28-10-2009

119 reputação

7 Guias de autoria

Emblemas: 10

+7 emblemas

Equipe

Cal Poly, Team 19-3, Maness Fall 2009 Membro de Cal Poly, Team 19-3, Maness Fall 2009

CPSU-MANESS-F09S19G3

4 Membros

18 Guias de autoria

0 comentários

Adicionar um comentário

Adicionar comentário

Visualizar Estatísticas:

Últimas 24 horas: 0

Últimos 7 dias: 0

Últimos 30 dias: 0

Todo: 1,992