Introdução

Use this guide to remove and install a new lower case on your OLPC XO-4 Touch.

Peças

Não são necessárias peças.

Turn the laptop upside-down, with the handle facing away from you.
  • Turn the laptop upside-down, with the handle facing away from you.

Adicionar comentário

Pull the lock tabs towards the green outer edges of the laptop. Hold the left lock tab in the unlock position until the battery is completely removed in the next step.
  • Pull the lock tabs towards the green outer edges of the laptop.

  • Hold the left lock tab in the unlock position until the battery is completely removed in the next step.

Adicionar comentário

Lift up on the middle of the battery to remove it from the device. Lift up on the middle of the battery to remove it from the device.
  • Lift up on the middle of the battery to remove it from the device.

Adicionar comentário

Remove the two 2mm Phillips #1 screws from beneath the battery lock tabs. Remove the two 2mm Phillips #1 screws from beneath the battery lock tabs.
  • Remove the two 2mm Phillips #1 screws from beneath the battery lock tabs.

Adicionar comentário

Flip the laptop over to its normal position. Lift the two antennas on both sides to unlock the screen. Open the laptop.
  • Flip the laptop over to its normal position.

  • Lift the two antennas on both sides to unlock the screen.

  • Open the laptop.

Adicionar comentário

Be careful not to pull the keyboard too far because there is still a ribbon cable attached to the bottom. Gently lift up on the back of the keyboard.
  • Be careful not to pull the keyboard too far because there is still a ribbon cable attached to the bottom.

  • Gently lift up on the back of the keyboard.

  • Pull the keyboard up far enough to expose the ribbon cable.

Adicionar comentário

Gently lift up on the black connector to release the ribbon cable. Gently pull the blue plastic tab up and away from the black connector.
  • Gently lift up on the black connector to release the ribbon cable.

  • Gently pull the blue plastic tab up and away from the black connector.

  • Remove the keyboard from the laptop.

Adicionar comentário

Close and flip the laptop over so you are looking at the battery compartment Remove the five 4mm Phillips #1 screws from inside the battery compartment
  • Close and flip the laptop over so you are looking at the battery compartment

  • Remove the five 4mm Phillips #1 screws from inside the battery compartment

Adicionar comentário

Flip the laptop over, showing the top of the device. Open the laptop and rotate the screen ninety degrees. Tilt the screen so the lower right corner of the screen is closer to the lower case.
  • Flip the laptop over, showing the top of the device.

  • Open the laptop and rotate the screen ninety degrees.

  • Tilt the screen so the lower right corner of the screen is closer to the lower case.

Adicionar comentário

Push in and lift up on the keyboard edge of the white handle piece. Pull the piece towards yourself to remove it from the laptop. Pull the piece towards yourself to remove it from the laptop.
  • Push in and lift up on the keyboard edge of the white handle piece.

  • Pull the piece towards yourself to remove it from the laptop.

Adicionar comentário

Remove the four 4mm Phillips #1 screws attaching the green trim to the body of the computer.
  • Remove the four 4mm Phillips #1 screws attaching the green trim to the body of the computer.

Adicionar comentário

Pry off the rear green trim piece. Pry off the rear green trim piece.
  • Pry off the rear green trim piece.

Adicionar comentário

Be careful not to pull the bottom portion of the laptop completely off, as there is a cable connecting it to the laptop. Slide the green trim pieces away from the screen. This should release the entire bottom portion of the laptop.
  • Be careful not to pull the bottom portion of the laptop completely off, as there is a cable connecting it to the laptop.

  • Slide the green trim pieces away from the screen.

  • This should release the entire bottom portion of the laptop.

Adicionar comentário

Unplug the cable from the mouse buttons controller to completely remove the lower frame from the device. Unplug the cable from the mouse buttons controller to completely remove the lower frame from the device. Unplug the cable from the mouse buttons controller to completely remove the lower frame from the device.
  • Unplug the cable from the mouse buttons controller to completely remove the lower frame from the device.

Adicionar comentário

Rotate the entire lower assembly up slightly, and pull it away from the screen to free it from the screen hinge. There may be some adhesive holding the cable to the metal plate. Gently pull the cable off of the plate if it is stuck.
  • Rotate the entire lower assembly up slightly, and pull it away from the screen to free it from the screen hinge.

  • There may be some adhesive holding the cable to the metal plate. Gently pull the cable off of the plate if it is stuck.

Adicionar comentário

Conclusão

To reassemble your device, follow these instructions in reverse order.

Uma outra pessoa concluiu este guia.

Michael Kellerman

Member since: 24-01-2013

46 reputação

3 Guides authored

Equipe

Cal Poly, Team 3-30, Amido Winter 2013 Membro de Cal Poly, Team 3-30, Amido Winter 2013

CPSU-AMIDO-W13S3G30

3 Membros

6 Guides authored

Adicionar comentário

Visualizar Estatísticas:

Últimas 24 horas: 0

Últimos 7 dias: 0

Últimos 30 dias: 0

Todo: 161