Nintendo DS Main Circuit Board Replacement

Esta versão pode conter edições incorretas. Mude para o último instantâneo verificado.

O que você precisa

Passo 1

Este passo não foi traduzido. Ajude a traduzi-lo

Remove the cartridge from the console.
Use a Phillips #00 Screwdriver to remove the screw securing the battery door to the rear case.
Remove the battery door.
In the images, it shows that the fixer is using a flathead screwdriver. This flathead screwdriver will work just like the Phillips #00 Screwdriver.

Editar

Passo 2

Este passo não foi traduzido. Ajude a traduzi-lo

Use a plastic opening tool or spudger to pry out the battery from the bottom. If a plastic opening tool or spudger isn't available, your fingernails may work.

Editar

Passo 3

Este passo não foi traduzido. Ajude a traduzi-lo

Remove the battery from the Nintendo DS.

Editar

Passo 4

Este passo não foi traduzido. Ajude a traduzi-lo

Remove the seven 6.4mm Y00 screws located on the back.
If your DS has a lanyard attached to it, you can remove it to make the process of opening the top-left screw easier.

Editar

Passo 5

Este passo não foi traduzido. Ajude a traduzi-lo

With your hands, pry the back panel off the main case.
Separate the back from the front, and set it aside.

Editar

If some of your screws spin free but can’t be removed, it maybe that the screw posts have separated from the shell.

This makes separating the back panel more difficult, but it will still work.

The plastic used for the original silver nds may be the most prone to the UV damage that causes the plastic to become brittle.

Del Riordan - 9 de jan de 2021 Responder

Passo 6

Este passo não foi traduzido. Ajude a traduzi-lo

Using a Phillips #00 screwdriver, remove the four screws on the circuit board.
Be careful NOT to slip with the screwdriver, you can damage the circuit board!

Editar

Passo 7

Este passo não foi traduzido. Ajude a traduzi-lo

Unlock the two large ribbon cables by moving the black clip up.
Carefully pull the ribbon cables down and out with your fingers.
Do not use pliers to pull the cables, as they can be damaged easily.

Editar

Benutze für die nächsten Schritte besser einen Spudger und keine Pinzette,

sonst läufst du Gefahr eines der Kabel oder die Platine selbst zu beschädigen.

Better use a Spudger, not a Tweezer for the next Steps.

That minimize the risk to demolish one of the wires or the mainboard himself.

Christian - 26 de mar de 2020 Responder

That’s what i did but it didn’t work

TrequanBlake - 9 de out de 2020 Responder

Passo 8

Este passo não foi traduzido. Ajude a traduzi-lo

Locate the two small ribbon cables, beneath the rightmost large ribbon cable.
Slide the locks for the small ribbon cables down to the side, and remove the cables.
It may be useful to use tweezers to remove the small ribbon cables.
Be careful not to damage the delicate ribbon cables.

Editar

Does anyone know where I can get a new connector for the P6 connector? I can only find them for the ds lite

Matthew Leto - 18 de ago de 2022 Responder

"Slide the locks for the small ribbon cables down to the side, and remove the cables." Could mention that you are pushing them from the right to the left/towards where the cables are coming from. To the side sounds like towards the right edge

M Beck - 25 de fev de 2024 Responder

Passo 9

Este passo não foi traduzido. Ajude a traduzi-lo

Locate the Wifi antenna pigtail connector.
Remove the antenna by grasping it at the head with tweezers. Using a slight rocking motion, pull up to dislodge the connector.

Editar