Conserte seus objetos

Direito de executar reparos

Loja

Nintendo 64 Motherboard Replacement

Em destaque

Escrito Por: tonymag28 (e 11 outros contribuidores)
  • Comentários: 3
  • Favoritos: 41
  • Execuções: 32

Guia em destaque

Dificuldade

Fácil

Passos

16

Tempo necessário

15 - 20 minutos

Partes

3

Sinalizadores

1

Featured Guide

Guia em destaque

Este guia foi considerado super bacana pela equipe da iFixit.

Introdução

This guide will show how to replace the Nintendo 64 motherboard.

  1. Remove the expansion pack cover by pushing in the tab and pulling out.

    • Remove the expansion pack cover by pushing in the tab and pulling out.

    Editar

  2. If your system uses a jumper pack, the same procedure applies to remove it.

    • If your system uses a jumper pack, the same procedure applies to remove it.

    • A small spoon can be used in place of a spudger.

    • Lever the expansion pack out using a metal spudger.

    Editar

  3. Remove the six screws on the bottom side indicated in the example with a gamebit head or screwdriver.

    • Remove the six screws on the bottom side indicated in the example with a gamebit head or screwdriver.

    Editar

  4. Remove the two front feet of the N64.

    • Remove the two front feet of the N64.

    Editar

  5. Rotate to top side up and lift off top cover.

    • Rotate to top side up and lift off top cover.

    Editar

  6. Remove the fourteen screws indicated in the example using the larger Phillips screwdriver. Remove the fourteen screws indicated in the example using the larger Phillips screwdriver.

    • Remove the fourteen screws indicated in the example using the larger Phillips screwdriver.

    Editar

  8. Remove the metal plate indicated in the example by sliding it back and then lifting it up. Remove the metal plate indicated in the example by sliding it back and then lifting it up.

    • Remove the metal plate indicated in the example by sliding it back and then lifting it up.

    Editar

  9. Remove the two screws indicated in the example using the smaller Phillips screwdriver.

    • Remove the two screws indicated in the example using the smaller Phillips screwdriver.

    Editar

  10. Remove the screw to the right of the LED light using the larger Phillips screwdriver.

    • Remove the screw to the right of the LED light using the larger Phillips screwdriver.

    Editar

  11. Remove the small metal bracket from the back of the expansion pack slot.

    • Remove the small metal bracket from the back of the expansion pack slot.

    Editar

  12. Remove the small metal bracket from the front of the expansion pack slot with the metal spudger. Remove the small metal bracket from the front of the expansion pack slot with the metal spudger.

    • Remove the small metal bracket from the front of the expansion pack slot with the metal spudger.

    Editar

  13. Remove the small metal bracket behind the expansion slot using the spudger. Remove the small metal bracket behind the expansion slot using the spudger.

    • Remove the small metal bracket behind the expansion slot using the spudger.

    Editar

  14. Remove the seven screws indicated in the example using the larger Phillips screwdriver. Remove the seven screws indicated in the example using the larger Phillips screwdriver.

    • Remove the seven screws indicated in the example using the larger Phillips screwdriver.

    Editar

  15. Lift off and remove the metal plate as indicated in the example.

    • Lift off and remove the metal plate as indicated in the example.

    Editar

  16. Remove the four screws indicated using the #1 Phillips screwdriver.

    • Remove the four screws indicated using the #1 Phillips screwdriver.

    Editar

  17. Lift up and remove the motherboard.

    • Lift up and remove the motherboard.

    Editar
Conclusão

To reassemble your device, follow these instructions in reverse order.

32 outras pessoas concluíram este guia.

Autor

com 11 outros contribuidores

tonymag28

Membro desde: 28/10/2009

1.939 Reputação

3 Guias de autoria

Emblemas: 13

+10 outros emblemas

Equipe

Cal Poly, Team 5-4, Regan Fall 2009 Membro de Cal Poly, Team 5-4, Regan Fall 2009

CPSU-REGAN-F09S5G4

7 Membros

6 Guias de autoria

Um comentário

Adicionar um comentário

4.2mm doesn't seem right. When I looked to purchase all I saw was 4.5mm and now that I have one in my hand it seems to fit very precisely on the screws on my N64.

negroslim - Responder

Adicione um comentário

Exibir estatísticas:

Últimas 24 horas: 15

Últimos 7 dias: 60

Últimos 30 dias: 243

Duração total: 53,434