Nikon D800 Top LCD Cover Glass Replacement

Escrito Por: Evan Noronha (e 2 outros contribuidores)

Comentários: 62
Favoritos: 1
Execuções: 8

Nikon D800 Top LCD Cover Glass Replacement

Dificuldade

Moderado

Passos

Tempo necessário

Sugerir um tempo??

Introdução

Follow this guide to replace a cracked top LCD cover glass on your Nikon D800. This procedure will fix a broken top cover glass, but not a cracked display.

Ferramentas

Comprar estas ferramentas

Peças

Nenhum componente especificado.

Passo 1 iOpener Heating

We recommend that you clean your microwave before proceeding, as any nasty gunk on the bottom may end up stuck to the iOpener.

Place the iOpener in the center of the microwave.

We recommend that you clean your microwave before proceeding, as any nasty gunk on the bottom may end up stuck to the iOpener.
Place the iOpener in the center of the microwave.
For carousel microwaves: Make sure the plate spins freely. If your iOpener gets stuck, it may overheat and burn.

Editar

Passo 2

Heat the iOpener for thirty seconds.
Throughout the repair procedure, as the iOpener cools, reheat it in the microwave for an additional thirty seconds at a time.
Be careful not to overheat the iOpener during the repair. Overheating may cause the iOpener to burst.
Never touch the iOpener if it appears swollen.
If the iOpener is still too hot in the middle to touch, continue using it while waiting for it to cool down some more before reheating. A properly heated iOpener should stay warm for up to 10 minutes.

Editar

Passo 3

Remove the iOpener from the microwave, holding it by one of the two flat ends to avoid the hot center.

Remove the iOpener from the microwave, holding it by one of the two flat ends to avoid the hot center.
The iOpener will be very hot, so be careful when handling it. Use an oven mitt if necessary.

Editar

Passo 4 Top LCD Glass

Lay a warm iOpener over the LCD glass to soften the adhesive holding it in place.

Lay a warm iOpener over the LCD glass to soften the adhesive holding it in place.
The following steps involve prying the glass up and out of the camera. If at any time you encounter too much resistance, reheat and reapply the iOpener to loosen the adhesive.

Editar

Passo 5

Before beginning, lay a piece of packing tape over the broken glass to hold it together during the removal procedure.

Insert a curved razor blade between the LCD glass cover and the body of D800.

Before beginning, lay a piece of packing tape over the broken glass to hold it together during the removal procedure.
Insert a curved razor blade between the LCD glass cover and the body of D800.
The blade is sharp, and can damage the LCD. When completing this repair, do not insert the knife more than 3 mm into the LCD window to avoid damaging the display.

Editar

Passo 6

Slide the curved razor blade along the front edge of the LCD.

Slide the curved razor blade along the front edge of the LCD.

Editar

Passo 7

Bring the blade around the corner of the LCD closest to the shutter button.

Bring the blade around the corner of the LCD closest to the shutter button.

Editar

Passo 8

Cut along the right edge of the display.

Cut along the right edge of the display.

Editar

Passo 9

Cut along the left edge of the display.

Editar

Passo 10

Insert the curved razor blade between the long edge of the LCD and the body of the D800.

Use the blade to pry the edge of the glass off the LCD.

Insert the curved razor blade between the long edge of the LCD and the body of the D800.
Use the blade to pry the edge of the glass off the LCD.

Editar

Passo 11

Work your blade towards the corner nearest the lens.

Again, use the blade to separate the glass from the LCD panel.

Work your blade towards the corner nearest the lens.
Again, use the blade to separate the glass from the LCD panel.

Editar

Passo 12

While lifting up with the razor blade, insert a plastic opening pick underneath the LCD glass.

While lifting up with the razor blade, insert a plastic opening pick underneath the LCD glass.
Remove the razor blade.

Editar

Passo 13

Slide the pick along the top edge of the glass, prying up on the glass against the plastic body as you go.

Slide the pick along the top edge of the glass, prying up on the glass against the plastic body as you go.

Editar

Passo 14

Leave the first opening pick underneath the front-right corner of the glass.

Insert a second opening pick underneath the panel from the back-left side of the display.

Slide the pick right, prying up the glass panel as you go.

Leave the first opening pick underneath the front-right corner of the glass.
Insert a second opening pick underneath the panel from the back-left side of the display.
Slide the pick right, prying up the glass panel as you go.

Editar

Passo 15

Once the glass is mostly separated from the camera, peel the panel completely off the LCD screen.

At this point there may be some adhesive tape connecting the glass to the camera. If so, simply pull the glass up until it's free.

Once the glass is mostly separated from the camera, peel the panel completely off the LCD screen.
At this point there may be some adhesive tape connecting the glass to the camera. If so, simply pull the glass up until it's free.

Editar

Passo 16

Using rubbing alcohol and a q-tip, clean the old adhesive strips and any residue off the LCD screen.

Using rubbing alcohol and a q-tip, clean the old adhesive strips and any residue off the LCD screen.

Editar

Passo 17

Carefully align the new LCD protective glass over the display.

Lower the left edge of the glass onto the display and press it firmly against the edge of the LCD window.

Carefully align the new LCD protective glass over the display.
Lower the left edge of the glass onto the display and press it firmly against the edge of the LCD window.
Ease the right edge into place.