Introdução

This is a step-by-step guide on how to remove the charging port in a Netgear Arlo

Remove the 2 (3.5mm) housing screws with a J0 screwdriver.
  • Remove the 2 (3.5mm) housing screws with a J0 screwdriver.

Adicionar comentário

Slide the unlocked battery cover forward to remove 2 (3.5mm) screws, that are behind the cover. Slide the unlocked battery cover forward to remove 2 (3.5mm) screws, that are behind the cover.
  • Slide the unlocked battery cover forward to remove 2 (3.5mm) screws, that are behind the cover.

Adicionar comentário

Open the battery cover and remove the  2 (3.5mm") screws from under the cover.
  • Open the battery cover and remove the 2 (3.5mm") screws from under the cover.

Adicionar comentário

Use a plastic opening tool to start separating the plastic housing from the front side of the battery cover. Next,  start separating the plastic cover from the rear of the plastic housing, and work your way down the seam line. Make sure the plastics snaps on the front of the plastic get unhooked from the grey plastic ring around the front of the camera.
  • Use a plastic opening tool to start separating the plastic housing from the front side of the battery cover.

  • Next, start separating the plastic cover from the rear of the plastic housing, and work your way down the seam line.

  • Make sure the plastics snaps on the front of the plastic get unhooked from the grey plastic ring around the front of the camera.

Adicionar comentário

Remove the screw (3.5mm) near the sync button holding the opposite side of the camera on. Remove the second screw (3.5mm) on the back of the camera to remove the second housing. Once the screws are removed use an opening tool to pry back the second plastic mount.
  • Remove the screw (3.5mm) near the sync button holding the opposite side of the camera on.

  • Remove the second screw (3.5mm) on the back of the camera to remove the second housing.

  • Once the screws are removed use an opening tool to pry back the second plastic mount.

Adicionar comentário

Remove 4 (6mm) large screws with a J00 screwdriver.
  • Remove 4 (6mm) large screws with a J00 screwdriver.

  • There are 2 on each side. This will allow you to remove the clear housing from the white housing.

Adicionar comentário

Once screws are removed, pull apart the clear housing. Remove rod from camera cover.
  • Once screws are removed, pull apart the clear housing.

  • Remove rod from camera cover.

Adicionar comentário

Remove Large ribbon cable first to disconnect front of camera from main body. Remove 4 (3.5mm) small black screws from motherboard of the camera unit. Remove smaller ribbon cable from underneath yellow tape.
  • Remove Large ribbon cable first to disconnect front of camera from main body.

  • Remove 4 (3.5mm) small black screws from motherboard of the camera unit.

  • Remove smaller ribbon cable from underneath yellow tape.

Adicionar comentário

Once all ribbon cables are removed, remove the motherboard and camera assembly by pulling up on the black camera motherboard.
  • Once all ribbon cables are removed, remove the motherboard and camera assembly by pulling up on the black camera motherboard.

Adicionar comentário

Remove the 2 (.135") housing screws with a JIS00 screwdriver
  • Remove the 2 (.135") housing screws with a JIS00 screwdriver

Adicionar comentário

Remove 4 (.135") screws on the inside of the battery compartment using the JIS 00 screwdriver.
  • Remove 4 (.135") screws on the inside of the battery compartment using the JIS 00 screwdriver.

Adicionar comentário

Slide the two halves apart
  • Slide the two halves apart

Adicionar comentário

Remove the 2 (.135") screws holding the charging port on using the JIS 00 screwdriver.
  • Remove the 2 (.135") screws holding the charging port on using the JIS 00 screwdriver.

Adicionar comentário

Remove the ribbon by prying the black ribbon holder up using the opening tool. Pull the ribbon away from the charging port.
  • Remove the ribbon by prying the black ribbon holder up using the opening tool.

  • Pull the ribbon away from the charging port.

Adicionar comentário

Conclusão

To reassemble your device, follow these instructions in reverse order.

Brian Johnson

Member since: 21-03-2018

121 reputação

Autoria de 1 guia

Equipe

IUPUI, Team S2-G1, Freund Spring 2018 Membro de IUPUI, Team S2-G1, Freund Spring 2018

IUPUI-FREUND-S18S2G1

2 Membros

2 Guides authored

Adicionar comentário

Visualizar Estatísticas:

Últimas 24 horas: 2

Últimos 7 dias: 8

Últimos 30 dias: 31

Todo: 97