Ir para o conteúdo principal

Nerf N-Strike Elite Hail-Fire Inner Plastic Components Replacement

O que você precisa

  1. Nerf N-Strike Elite Hail-Fire Inner Plastic Components Replacement, Left Shell: passo 1, imagem 1 %32 Nerf N-Strike Elite Hail-Fire Inner Plastic Components Replacement, Left Shell: passo 1, imagem 2 %32 Nerf N-Strike Elite Hail-Fire Inner Plastic Components Replacement, Left Shell: passo 1, imagem 3 %32
    • Before disassembling your Nerf Hail-Fire, be sure to remove the batteries.

    • Remove the two 9.0 mm Phillips screws securing the battery compartment.

    • Slide the battery compartment out.

  2. Nerf N-Strike Elite Hail-Fire Inner Plastic Components Replacement: passo 2, imagem 1 %32
    • Remove the five 9.0 mm Phillips screws securing the trigger.

  3. Nerf N-Strike Elite Hail-Fire Inner Plastic Components Replacement: passo 3, imagem 1 %32 Nerf N-Strike Elite Hail-Fire Inner Plastic Components Replacement: passo 3, imagem 2 %32
    • Remove the single 11.0 mm Phillips screw securing the magazine cartridge chambers.

    • Pull the entire chamber upwards to separate it from the rest of the Nerf Gun.

  4. Nerf N-Strike Elite Hail-Fire Inner Plastic Components Replacement: passo 4, imagem 1 %32 Nerf N-Strike Elite Hail-Fire Inner Plastic Components Replacement: passo 4, imagem 2 %32 Nerf N-Strike Elite Hail-Fire Inner Plastic Components Replacement: passo 4, imagem 3 %32
    • Remove both halves of the ring by tugging on it upwards until the lock gets freed.

    • This requires quite a bit of force and if you are not careful, you may break the plastic lock.

  5. Nerf N-Strike Elite Hail-Fire Inner Plastic Components Replacement: passo 5, imagem 1 %32
    • Remove the four 9.0 mm Phillips screws from the newly revealed cylinder.

  6. Nerf N-Strike Elite Hail-Fire Inner Plastic Components Replacement: passo 6, imagem 1 %32
    • Remove the three 9.0 mm Phillips screws holding the top latch of the Nerf Gun together.

  7. Nerf N-Strike Elite Hail-Fire Inner Plastic Components Replacement: passo 7, imagem 1 %32
    • Remove the three 9.0 mm Phillips screws holding together the firing chamber.

    • Remove the single 7.0 mm Phillips screw below the barrel.

    • Remove the two 14.0 mm Philips screws using a screwdriver with a length of approximately 4.0 inches and a diameter of approximately 0.2 cm.

  8. Nerf N-Strike Elite Hail-Fire Inner Plastic Components Replacement: passo 8, imagem 1 %32
    • Remove the single 14.0 mm Phillips screw holding together the handle and the Nerf Gun.

  9. Nerf N-Strike Elite Hail-Fire Inner Plastic Components Replacement: passo 9, imagem 1 %32 Nerf N-Strike Elite Hail-Fire Inner Plastic Components Replacement: passo 9, imagem 2 %32
    • Remove the two 9.0 mm Phillips screws holding together the handle.

    • Remove the plastic cover of the handle.

  10. Nerf N-Strike Elite Hail-Fire Inner Plastic Components Replacement: passo 10, imagem 1 %32 Nerf N-Strike Elite Hail-Fire Inner Plastic Components Replacement: passo 10, imagem 2 %32
    • Insert one plastic opening tool inside one side of the orange part depicted in the picture.

    • Insert a second plastic opening tool to the other side of the orange part and gradually pull the piece out, freeing it from the handle.

  11. Nerf N-Strike Elite Hail-Fire Inner Plastic Components Replacement: passo 11, imagem 1 %32 Nerf N-Strike Elite Hail-Fire Inner Plastic Components Replacement: passo 11, imagem 2 %32 Nerf N-Strike Elite Hail-Fire Inner Plastic Components Replacement: passo 11, imagem 3 %32
    • Pull one end of the handle away from the orange latch.

    • Repeat the procedure on the other side to completely remove the handle from the rest of the Nerf Gun.

  12. Nerf N-Strike Elite Hail-Fire Inner Plastic Components Replacement: passo 12, imagem 1 %32 Nerf N-Strike Elite Hail-Fire Inner Plastic Components Replacement: passo 12, imagem 2 %32 Nerf N-Strike Elite Hail-Fire Inner Plastic Components Replacement: passo 12, imagem 3 %32
    • Lift the entire left shell slowly. The process should be easy and if there is any resistance, there is something wrong. You may have forgotten a screw.

    • Completely remove the left shell from the rest of the Nerf Gun.

  13. Nerf N-Strike Elite Hail-Fire Inner Plastic Components Replacement, Inner Plastic Components: passo 13, imagem 1 %32 Nerf N-Strike Elite Hail-Fire Inner Plastic Components Replacement, Inner Plastic Components: passo 13, imagem 2 %32 Nerf N-Strike Elite Hail-Fire Inner Plastic Components Replacement, Inner Plastic Components: passo 13, imagem 3 %32
    • Remove the cartridge support.

  14. Nerf N-Strike Elite Hail-Fire Inner Plastic Components Replacement: passo 14, imagem 1 %32 Nerf N-Strike Elite Hail-Fire Inner Plastic Components Replacement: passo 14, imagem 2 %32 Nerf N-Strike Elite Hail-Fire Inner Plastic Components Replacement: passo 14, imagem 3 %32
    • Remove the handle crank.

  15. Nerf N-Strike Elite Hail-Fire Inner Plastic Components Replacement: passo 15, imagem 1 %32 Nerf N-Strike Elite Hail-Fire Inner Plastic Components Replacement: passo 15, imagem 2 %32
    • Remove the clear plastic barrel cover.

  16. Nerf N-Strike Elite Hail-Fire Inner Plastic Components Replacement: passo 16, imagem 1 %32 Nerf N-Strike Elite Hail-Fire Inner Plastic Components Replacement: passo 16, imagem 2 %32
    • Remove the firing pin.

Conclusão

To reassemble your device, follow these instructions in reverse order.

Uma outra pessoa concluiu este guia.

sage

Membro desde: 01/24/14

301 Reputação

Autoria de 3 guias

Equipe

Cal Poly, Team 13-13, Regan Winter 2014 Membro de Cal Poly, Team 13-13, Regan Winter 2014

CPSU-REGAN-W14S13G13

Membros da 4

Autoria de 7 guias

0 comentários

Adicione um comentário

Exibir estatísticas:

Últimas 24 horas: 2

Últimos 7 dias: 2

Últimos 30 dias: 9

Duração total: 1,181