Pular para o conteúdo principal

Introdução

Prerequisite-only guide for removing the midframe from the Moto G4, in order to access internal components for servicing.

Peças

Nenhum componente especificado.

  1. Insert a fingernail or a spudger into the notch on the bottom edge of the phone, near the charge port. Gently twist or pry to open a small gap between the back cover and the body of the phone. While keeping your tool (or fingernail) inserted into the gap between the back cover and the body of the phone, slide it around the corner to begin loosening the plastic clips holding the cover in place.
    • Insert a fingernail or a spudger into the notch on the bottom edge of the phone, near the charge port.

    • Gently twist or pry to open a small gap between the back cover and the body of the phone.

    • While keeping your tool (or fingernail) inserted into the gap between the back cover and the body of the phone, slide it around the corner to begin loosening the plastic clips holding the cover in place.

  2. Slide your tool all along the side of the phone to separate more of the clips securing the back cover. Slide your tool all along the side of the phone to separate more of the clips securing the back cover.
    • Slide your tool all along the side of the phone to separate more of the clips securing the back cover.

  3. Keep your tool inserted slightly under the back cover, and slide it around the top corner. If necessary, continue prying around the remaining edges of the phone until the back cover comes free. If necessary, continue prying around the remaining edges of the phone until the back cover comes free.
    • Keep your tool inserted slightly under the back cover, and slide it around the top corner.

    • If necessary, continue prying around the remaining edges of the phone until the back cover comes free.

  4. Remove the back cover. To install the back cover, carefully position it over the phone and then press gently all around the edges until you feel the clips snap into place.
    • Remove the back cover.

    • To install the back cover, carefully position it over the phone and then press gently all around the edges until you feel the clips snap into place.

  5. Push to eject and remove the MicroSD and SIM cards (if installed). Push to eject and remove the MicroSD and SIM cards (if installed). Push to eject and remove the MicroSD and SIM cards (if installed).
    • Push to eject and remove the MicroSD and SIM cards (if installed).

  6. Use a spudger to pry up the rubber cover for the camera flash connector. Use a spudger to pry up the rubber cover for the camera flash connector.
    • Use a spudger to pry up the rubber cover for the camera flash connector.

  7. Remove the rubber cover.
    • Remove the rubber cover.

  8. Use a spudger to disconnect the camera flash connector by prying it straight up. Use a spudger to disconnect the camera flash connector by prying it straight up.
    • Use a spudger to disconnect the camera flash connector by prying it straight up.

  9. Use a T3 Torx driver to remove the nineteen identical 3.1 mm screws securing the midframe.
    • Use a T3 Torx driver to remove the nineteen identical 3.1 mm screws securing the midframe.

  10. Insert a spudger under the midframe at the top left corner, and gently twist to separate it from the body of the phone.
    • Insert a spudger under the midframe at the top left corner, and gently twist to separate it from the body of the phone.

  11. Remove the midframe.
    • Remove the midframe.

Conclusão

To reassemble your device, follow these instructions in reverse order.

Jeff Suovanen

Membro desde: 06-08-2013

248.006 reputação

212 Guias de autoria

Equipe

iFixit Membro de iFixit

Community

104 Membros

9.254 Guias de autoria

Adicionar comentário

Visualizar Estatísticas:

Últimas 24 horas: 0

Últimos 7 dias: 0

Últimos 30 dias: 0

Todo: 30