Ir para o conteúdo principal

Conserte seus objetos

Direito de executar reparos

Peças e ferramentas

Introdução

The LCD screen is held into the camera by the outer casing and an internal bracket. It is one component, so there isn't a way to just replace the LCD screen. Once screen is out of the bracket, wires must be removed to completely remove the LCD screen.

Peças

Nenhum componente especificado.

  1. Locate and remove the silver screws on each side of the camera. Use the Phillips #00 Screwdriver to unscrew all 2.0mm (4 instances) and 4.0mm (2 instances) screws. Use the Phillips #00 Screwdriver to unscrew all 2.0mm (4 instances) and 4.0mm (2 instances) screws.
    • Locate and remove the silver screws on each side of the camera.

    • Use the Phillips #00 Screwdriver to unscrew all 2.0mm (4 instances) and 4.0mm (2 instances) screws.

  2. Then, carefully pry apart the front and back outer casing away from the internal components. Be aware of the ribbon wire that will disconnect when the casing is detached. Be aware of the ribbon wire that will disconnect when the casing is detached.
    • Then, carefully pry apart the front and back outer casing away from the internal components.

    • Be aware of the ribbon wire that will disconnect when the casing is detached.

  3. Kits para Nintendo Switch

    A quick fix to get back in the game

    Shop Switch Kits

    Kits para Nintendo Switch

    A quick fix to get back in the game

    Shop Switch Kits
  4. The LCD screen has wires connecting it to the rest of the camera. A bracket holds the LCD in place, so there are no screws beyond this point.
    • The LCD screen has wires connecting it to the rest of the camera. A bracket holds the LCD in place, so there are no screws beyond this point.

    • The screen also has a ribbon wire connected at the bottom of the screen. (See 2nd picture)

  5. Detach the strip at the bottom from the LCD screen. Gently slide the spudger underneath the screen.
    • Detach the strip at the bottom from the LCD screen.

    • Gently slide the spudger underneath the screen.

    • Note: from the side or a corner is easiest.

    • Press the tip of the spudger down as far is you can, slowly prying away from the bracket.

  6. The screen is not detached, but is removed from its bracket. Note: Wires are still connecting the screen to the camera at the bottom corners.
    • The screen is not detached, but is removed from its bracket. Note: Wires are still connecting the screen to the camera at the bottom corners.

    • Check to make sure wires are connected, so it will receive proper power supply.

    • To remove the bracket for the LCD screen, remove these 1.5 mm (2 instances) screws using the #00 Phillips screwdriver.

Conclusão

To install new LCD screen you will have to reconnect the wires and properly place in bracket. Make sure to reattach the ribbon wire before finishing repairs.

Uma outra pessoa concluiu este guia.

Keith Sechrist

Membro desde: 11-03-2013

22 Reputação

2 Guias de autoria

equipe

Clemson, Team 12-4, Benson Spring 2013 Membro de Clemson, Team 12-4, Benson Spring 2013

CLEM-BENSON-S13S12G4

3 Membros

7 Guias de autoria

Great procedure, thank you.

Do you know where I can buy the LCD replacement part?

I have a Konica Minolta Dimage X1 8.0 MP

mscir - Responder

Adicione um comentário

Exibir estatísticas:

Últimas 24 horas: 0

Últimos 7 dias: 0

Últimos 30 dias: 6

Duração total: 579