Introdução

Use this guide to replace the AirPort card in your Mac Pro Late 2013.

  1. Slide the lock switch to the right, to the unlocked position.
    • Slide the lock switch to the right, to the unlocked position.

    Adicionar comentário

  2. Lift the outer case straight up off the Mac Pro.
    • Lift the outer case straight up off the Mac Pro.

    • It may help to push down on the center of the fan while lifting the case up.

    Adicionar comentário

    • Remove five 5.1 mm T10 Torx screws from around the outer perimeter of the fan assembly.

    You don't have to remove the fan assy to get to the wifi board & card. It can be done with the fan assy still attached.

    Fat Mango - Responder

    Fat Mango is correct. That said. If you do pull the fan assembly note that the screws are all held in with blue Permatex and breaking them free takes a fair amount of effort. Getting a good set of Torx screwdrivers is a must.

    Jim WIlson - Responder

    • The fan assembly is attached to the rest of the computer by two cables on the IO board side.

    • Tilt the assembly up away from the IO board.

    • Do not try to remove the fan assembly yet, as it is still attached by two cables.

    Adicionar comentário

    • While supporting the fan assembly with one hand, loosen the two T7 captive screws in the fan cable bracket.

    • These screws are captive in the Mac Pro. Do not try to remove these screws from your Mac Pro.

    On my Mac Pro (assembled mid-2017) these are T8 screws. In fact, there were no T7 screws anywhere in my machine.

    mark33 - Responder

    • Use a pair of tweezers to pull the fan cable bracket away from the fan assembly.

    Adicionar comentário

  3. Spread Fixmas Cheer
    Get $12 off your purchase of $50 or more with code FIXMAS12
    Spread Fixmas Cheer
    Get $12 off your purchase of $50 or more with code FIXMAS12
    • Use the flat end of a spudger to disconnect the fan assembly ribbon cable from the IO board.

    Adicionar comentário

    • Disconnect the fan assembly antenna cable from the IO board.

    • Remove the fan assembly from the Mac Pro.

    You don't have to remove the fan assy to do the steps below. They can be done with the fan assy still attached.

    Fat Mango - Responder

    • Use the flat end of a spudger to pry the fan assembly lid up off the fan assembly.

    • Remove the fan assembly lid.

    There is a thin circle of double sided adhesive that must be loosened in order to remove the plastic cover.

    somethingorother - Responder

    • Remove the three 3.7 mm T4 screws securing the metal cover to the AirPort board bay.

    I had better luck using a T5 driver.

    somethingorother - Responder

    Same here. Mine were T5, not T4.

    Carsten Clark - Responder

    • Lift and remove the metal cover from the AirPort board bay.

    Adicionar comentário

    • Use the tip of a spudger to flip the ZIF retaining tab on the fan assembly ribbon cable connector.

    • Remove the fan assembly ribbon cable from its ZIF socket.

    Adicionar comentário

    • Use the tip of a spudger to flip the ZIF retaining tab on the fan ribbon cable.

    • Disconnect the fan ribbon cable.

    Adicionar comentário

    • Use the tip of a spudger to disconnect the four AirPort antenna cables from the AirPort card.

    Adicionar comentário

    • Remove three 3.7 mm T4 screws securing the AirPort board to the fan assembly.

    These screws were also T5, not T4, for me.

    Carsten Clark - Responder

    • Remove the AirPort board and card from the fan assembly.

    Adicionar comentário

    • Remove the two 3.7 mm T4 Torx screws securing the AirPort card to the AirPort board.

    And, finally, so were these!

    Carsten Clark - Responder

    • Slide the AirPort card out of its socket in the AirPort board.

    I suspect the newer Airport card (802.11ac) Apple P/N 653-0014 will work here.

    Dan - Responder

Conclusão

To reassemble your device, follow these instructions in reverse order.

2 outras pessoas concluíram este guia.

Andrew Optimus Goldberg

Member since: 17-10-2009

394.036 reputação

412 Guides authored

Equipe

iFixit Membro de iFixit

Community

113 Membros

7.288 Guides authored

Is there a way to replace the Mac Pro Airport card with a more recent one, like when you insert a recent one in an old macbook pro to get new features such as "unlock my mac with my apple watch" ? This is an interesting question that remains unanswered (until now ?)

Vincent Monteil - Responder

You show how to replace it but I can’t buy it from ifixit….why?

Sanong - Responder

Adicionar comentário

Visualizar Estatísticas:

Últimas 24 horas: 9

Últimos 7 dias: 22

Últimos 30 dias: 63

Todo: 3,571