Conserte seus objetos Comunidade Loja

Logitech Dual Action Triggers Repair

O que você precisa

  1. Logitech Dual Action Triggers Repair, Logitech Dual Action Triggers Repair: passo 1, imagem 1 %32

    • To get into the controller, you will need to unscrew the 7 screws on the back.

    • You will have to remove the bottom oval sticker to reveal the screw circled in red.

    Editar

  2. Logitech Dual Action Triggers Repair: passo 2, imagem 1 %32 Logitech Dual Action Triggers Repair: passo 2, imagem 2 %32

    • With the screws removed, turn the controller upside down and separate the front end from the back end.

    • It is likely that the buttons will fall out of place, so as you open the controller, try to keep track of where the pieces go.

    Editar

  3. Logitech Dual Action Triggers Repair: passo 3, imagem 1 %32

    • There should be 4 circular buttons labeled 1-4, 4 smaller circular buttons for the D-Pad, and 3 oval shaped buttons.

    Editar

  5. Logitech Dual Action Triggers Repair: passo 4, imagem 1 %32 Logitech Dual Action Triggers Repair: passo 4, imagem 2 %32 Logitech Dual Action Triggers Repair: passo 4, imagem 3 %32

    • In the center of the controller, pull upwards on the USB cord.

    • Be careful not to pull hard enough to yank the wires connecting to the logic board.

    • With the wire out of the way, remove the screw it exposed. This will disconnect the logic board from the controller.

    Editar

  6. Logitech Dual Action Triggers Repair: passo 5, imagem 1 %32 Logitech Dual Action Triggers Repair: passo 5, imagem 2 %32 Logitech Dual Action Triggers Repair: passo 5, imagem 3 %32

    • To remove the triggers, push upwards from the back on them.

    • Once far enough, detach the logic board from the back cover piece and the triggers.

    Editar

  7. Logitech Dual Action Triggers Repair: passo 6, imagem 1 %32 Logitech Dual Action Triggers Repair: passo 6, imagem 2 %32

    • If the wire is unplugged solely from the logic board, you can fasten it back into its place.

    • Look at the second picture to see where the wires go.

    Editar

  8. Logitech Dual Action Triggers Repair: passo 7, imagem 1 %32 Logitech Dual Action Triggers Repair: passo 7, imagem 2 %32 Logitech Dual Action Triggers Repair: passo 7, imagem 3 %32

    • Unscrew the screw on the trigger to remove the back cover.

    • Once removed, carefully pull the back cover off.

    Editar

  9. Logitech Dual Action Triggers Repair: passo 8, imagem 1 %32

    • The 3 wires are soldered into the 3 spots circled on the picture.

    • You can now fasten the wire into the right spot on the trigger piece.

    Editar
Conclusão

To reassemble your device, follow these instructions in reverse order.

4 outras pessoas executaram este guia.

Autor(a)

com 6 outros contribuidores

Brian Neuman

Membro desde: 01/20/15

893 Reputação

Autoria de 3 guias

Emblemas: 10

+7 outros emblemas

Equipe

USF Tampa, Team 7-4, Remmell Winter 2015 Membro de USF Tampa, Team 7-4, Remmell Winter 2015

USFT-REMMELL-W15S7G4

Membros da 4

Autoria de 3 guias

2 comentários

Hi dear, can you say me the order of colours in the USB cable? I think green, white, red, black thin and black thick. Is It correct?

Cas - Responder

Where can I get conductive pads for this?

Ginga - Responder

Adicione um comentário

Exibir estatísticas:

Últimas 24 horas: 1

Últimos 7 dias: 30

Últimos 30 dias: 123

Duração total: 8,931