Introdução

This guide will walk you through the process of replacing the power and volume buttons in an LG Phoenix 2. This guide could be used when the buttons do not respond them being pressed. This guide may also be used when the buttons get stuck.

Place a fingernail in the notch at the bottom edge of the phone. Pull on the back cover with one hand while keeping the rest of the phone steady, and run your fingernail along the edge. Pull on the back cover with one hand while keeping the rest of the phone steady, and run your fingernail along the edge.
  • Place a fingernail in the notch at the bottom edge of the phone.

  • Pull on the back cover with one hand while keeping the rest of the phone steady, and run your fingernail along the edge.

Adicionar comentário

Place a fingernail in the notch at the bottom edge of the battery. Pull the battery out. Pull the battery out.
  • Place a fingernail in the notch at the bottom edge of the battery.

  • Pull the battery out.

Adicionar comentário

Locate the SIM card in the top  right corner on the back of the phone. Remove the SIM card by pushing it with your thumb from left to right.
  • Locate the SIM card in the top right corner on the back of the phone.

  • Remove the SIM card by pushing it with your thumb from left to right.

Adicionar comentário

Remove all 9 screws on the back by using a Phillips head #J00 screwdriver. To remove the screws  rotate them counterclockwise. To remove the screws  rotate them counterclockwise.
  • Remove all 9 screws on the back by using a Phillips head #J00 screwdriver.

  • To remove the screws rotate them counterclockwise.

Adicionar comentário

Insert a plastic opening tool in the split at the bottom of the phone (between the bottom shield and the rest of the phone). Pry the bottom shield to separate it from the phone. Once it is loose you should be able to remove it with your hand.
  • Insert a plastic opening tool in the split at the bottom of the phone (between the bottom shield and the rest of the phone).

  • Pry the bottom shield to separate it from the phone.

  • Once it is loose you should be able to remove it with your hand.

Adicionar comentário

Insert the flat end of the Spudger between the screen and the chromed frame. Once inserted, run the Spudger along the frame to separate the front part of the phone from the back shield. Once inserted, run the Spudger along the frame to separate the front part of the phone from the back shield.
  • Insert the flat end of the Spudger between the screen and the chromed frame.

  • Once inserted, run the Spudger along the frame to separate the front part of the phone from the back shield.

Adicionar comentário

The buttons are attached with adhesive to both sides of the back shield. To separate the orange cables insert a metallic Spudger underneath and gently pull up. Once the orange part is loose move to the next step. Once the orange part is loose move to the next step.
  • The buttons are attached with adhesive to both sides of the back shield. To separate the orange cables insert a metallic Spudger underneath and gently pull up.

  • Once the orange part is loose move to the next step.

Adicionar comentário

Remove the buttons frame on the back side the shield, by inserting a plastic opening tool underneath the frame. Remove the buttons frame on the back side the shield, by inserting a plastic opening tool underneath the frame. Remove the buttons frame on the back side the shield, by inserting a plastic opening tool underneath the frame.
  • Remove the buttons frame on the back side the shield, by inserting a plastic opening tool underneath the frame.

Adicionar comentário

The buttons are attached with adhesive. To separate them from the shield insert a metallic Spudger underneath and gently pull up. Once the part is loose you should be able to pass the backside orange cables through the  hole. Once the part is loose you should be able to pass the backside orange cables through the  hole.
  • The buttons are attached with adhesive. To separate them from the shield insert a metallic Spudger underneath and gently pull up.

  • Once the part is loose you should be able to pass the backside orange cables through the hole.

Adicionar comentário

Conclusão

To reassemble your device, follow these instructions in reverse order.

Esteban Ruibal

Member since: 14-02-2018

666 reputação

5 Guides authored

Equipe

USF Tampa, Team S2-G2, Eyestone Spring 2018 Membro de USF Tampa, Team S2-G2, Eyestone Spring 2018

USFT-EYESTONE-S18S2G2

4 Membros

5 Guides authored

Adicionar comentário

Visualizar Estatísticas:

Últimas 24 horas: 1

Últimos 7 dias: 2

Últimos 30 dias: 11

Todo: 67