Introdução

In this guide, you will learn how to repair and replace a loose or faulty shutter button on your Kodak PixPro AZ251.

Slide switch to open lock position. Slide switch to open lock position.
  • Slide switch to open lock position.

Adicionar comentário

Press down on the battery cover and slide outwards to open. Press down on the battery cover and slide outwards to open.
  • Press down on the battery cover and slide outwards to open.

Adicionar comentário

Remove the batteries.
  • Remove the batteries.

Adicionar comentário

Remove a total of four 5mm JIS #000 screws from around the camera: Two screws from the right side. Two screws from the left side.
  • Remove a total of four 5mm JIS #000 screws from around the camera:

    • Two screws from the right side.

    • Two screws from the left side.

Adicionar comentário

Remove the single 5mm Phillips #00 screw from the bottom.
  • Remove the single 5mm Phillips #00 screw from the bottom.

Adicionar comentário

Open the flash module. Remove the two 6mm JIS #00 screws found inside of the flash housing.
  • Open the flash module.

  • Remove the two 6mm JIS #00 screws found inside of the flash housing.

Adicionar comentário

Use a plastic opening tool to pry apart both halves of the camera. Remove the back panel. Remove the back panel.
  • Use a plastic opening tool to pry apart both halves of the camera.

  • Remove the back panel.

Adicionar comentário

Remove these three JIS #000 screws from the control board: 5mm screw.
  • Remove these three JIS #000 screws from the control board:

    • 5mm screw.

    • 4mm screw.

    • 2mm screw.

Adicionar comentário

Pull the small metal switch plate to the side.
  • Pull the small metal switch plate to the side.

Adicionar comentário

Pry the LCD screen out of the metal housing plate with a plastic opening tool. Pry the LCD screen out of the metal housing plate with a plastic opening tool.
  • Pry the LCD screen out of the metal housing plate with a plastic opening tool.

Adicionar comentário

Use a spudger to flip up the retaining flap on the display ribbon cable ZIF socket. Pull the orange cable out of the socket.
  • Use a spudger to flip up the retaining flap on the display ribbon cable ZIF socket.

  • Pull the orange cable out of the socket.

Adicionar comentário

Remove one 4mm JIS #000 screw from the top of the camera. Remove one 4mm JIS #000 screw from the top of the camera.
  • Remove one 4mm JIS #000 screw from the top of the camera.

Adicionar comentário

Using tweezers, disconnect the orange cable connection at the top of the motherboard. Using tweezers, disconnect the orange cable connection at the top of the motherboard.
  • Using tweezers, disconnect the orange cable connection at the top of the motherboard.

Adicionar comentário

Pull the mode dial up and off of the camera. Rotate carefully to avoid breaking the screw attaching the top side cover to the main body of the camera.
  • Pull the mode dial up and off of the camera.

  • Rotate carefully to avoid breaking the screw attaching the top side cover to the main body of the camera.

Adicionar comentário

Turn camera upside down. Remove the six 2mm JIS #000 screws from the metal base of the shutter button.
  • Turn camera upside down.

  • Remove the six 2mm JIS #000 screws from the metal base of the shutter button.

Adicionar comentário

Remove the metal base and ribbon cables. Remove the metal base and ribbon cables.
  • Remove the metal base and ribbon cables.

Adicionar comentário

While holding the shutter button in place, remove the two 4mm JIS #000 screws from the base.
  • While holding the shutter button in place, remove the two 4mm JIS #000 screws from the base.

Adicionar comentário

Remove the plastic base of the shutter button using tweezers by pulling it straight upward.
  • Remove the plastic base of the shutter button using tweezers by pulling it straight upward.

Adicionar comentário

Remove the shutter button by pulling it out from the bottom side of the top cover.
  • Remove the shutter button by pulling it out from the bottom side of the top cover.

Adicionar comentário

Conclusão

To reassemble your device, follow these instructions in reverse order.

Rachel Llewellyn

Member since: 22-02-2018

497 reputação

3 Guides authored

Equipe

USF Tampa, Team S1-G1, Cagle Spring 2018 Membro de USF Tampa, Team S1-G1, Cagle Spring 2018

USFT-CAGLE-S18S1G1

4 Membros

7 Guides authored

Adicionar comentário

Visualizar Estatísticas:

Últimas 24 horas: 0

Últimos 7 dias: 1

Últimos 30 dias: 17

Todo: 44