Conserte seus objetos Comunidade Loja

Jumper Angelsounds JPD-100S Indicator Light Replacement

Introdução

Have a working knowledge of soldering before attempting to replace this part.

O que você precisa

  1. Jumper Angelsounds JPD-100S Indicator Light Replacement, Motherboard: passo 1, imagem 1 %32

    • Access the battery compartment

    • Remove the battery compartment lid and set it aside.

    • Disconnect the battery and set it aside.

    Editar

  2. Jumper Angelsounds JPD-100S Indicator Light Replacement: passo 2, imagem 1 %32 Jumper Angelsounds JPD-100S Indicator Light Replacement: passo 2, imagem 2 %32

    • Puncture the sticker in the battery compartment with a spudger to access the screw beneath it.

    Editar

  3. Jumper Angelsounds JPD-100S Indicator Light Replacement: passo 3, imagem 1 %32

    • Remove the 7mm Phillips #1 screw from the battery compartment.

    • Place the screw in a secure place.

    Editar

  5. Jumper Angelsounds JPD-100S Indicator Light Replacement: passo 4, imagem 1 %32 Jumper Angelsounds JPD-100S Indicator Light Replacement: passo 4, imagem 2 %32

    • Begin prying open the device.

    • Insert a plastic opening tool into the side groove about 2cm from the pink plastic component and pry open one side of the device.

    • Once the side is separated, leave the opening tool inside to prevent the two sides from closing.

    Editar

  6. Jumper Angelsounds JPD-100S Indicator Light Replacement: passo 5, imagem 1 %32 Jumper Angelsounds JPD-100S Indicator Light Replacement: passo 5, imagem 2 %32

    • Insert another plastic opening tool into the groove opposite to the side of the tool already inserted.

    • Create separation on that side until the white plastic component comes off entirely.

    • Place the white plastic component in a secure place.

    Editar

  7. Jumper Angelsounds JPD-100S Indicator Light Replacement: passo 6, imagem 1 %32

    • With your hand, remove the pink component.

    Editar

  8. Jumper Angelsounds JPD-100S Indicator Light Replacement: passo 7, imagem 1 %32

    • Remove the 7mm Phillips #1 screw in the middle of the motherboard.

    Editar

  9. Jumper Angelsounds JPD-100S Indicator Light Replacement, Indicator Light: passo 8, imagem 1 %32

    • Place the motherboard in a position that allows access it's underside.

    • Pre-heat the soldering iron.

    Editar

  10. Jumper Angelsounds JPD-100S Indicator Light Replacement: passo 9, imagem 1 %32 Jumper Angelsounds JPD-100S Indicator Light Replacement: passo 9, imagem 2 %32 Jumper Angelsounds JPD-100S Indicator Light Replacement: passo 9, imagem 3 %32

    • Desoldering

    • If steam is created when the soldering iron is touched to a wet sponge then the soldering iron is hot enough.

    • Use the soldering iron and soldering vacuum to unsolder the indicator light leads.

    • Plastic spacer holding indicator light may burn.

    Editar
Conclusão

To reassemble your device, follow these instructions in reverse order.

Autor(a)

com 3 outros contribuidores

Deron Rogers

Membro desde: 08/31/15

271 Reputação

Autoria de 2 guias

Emblemas: 14

+11 outros emblemas

Equipe

USF Tampa, Team 6-1, Remmell Fall 2015 Membro de USF Tampa, Team 6-1, Remmell Fall 2015

USFT-REMMELL-F15S6G1

Membros da 6

Autoria de 6 guias

0 comentários

Adicione um comentário

Exibir estatísticas:

Últimas 24 horas: 2

Últimos 7 dias: 4

Últimos 30 dias: 12

Duração total: 187