Introdução

This guide will walk you through the process of installing a zipper in your Patagonia down jacket. This is a tough repair and we recommend you have some sewing experience. For replacement parts or further assistance, contact Patagonia Customer Service.

  1. Unzip the jacket and fold back the bottom corner.
    • Unzip the jacket and fold back the bottom corner.

    • Identify the start of the seam that is holding the zipper in place.

    Adicionar comentário

  2. Using a seam ripper, gently remove the stitches on the inside of the zipper.
    • Using a seam ripper, gently remove the stitches on the inside of the zipper.

    • Be careful not to accidentally puncture or tear the jacket.

    Adicionar comentário

    • Bend the zipper teeth away from the zipper webbing to make it easier to reach the stitches that hold the zipper and webbing together.

    • Using the seam ripper, gently rip the seam between the zipper and zipper webbing.

    Adicionar comentário

    • Continue ripping the seam holding the zipper to the webbing until you come to the top of the seam.

    Adicionar comentário

    • When you come to the fold in the zipper webbing, insert the seam ripper between the two layers of webbing, and gently pull the stitches out.

    Adicionar comentário

    • The zipper should now be free from the jacket and can be discarded.

    Adicionar comentário

    • Identify where the zipper flap is still sewn into the jacket. Use the seam ripper to free the zipper flap from the jacket. The yellow rectangle in the photos above will help you identify the zipper flap.

    • Be careful not to damage the jacket with the seam ripper as you free the webbing.

    Adicionar comentário

    • Lay the jacket flat and measure from the base of the zipper to the collar, along the seam you just removed. In our case we measured 27 inches.

    • The jacket should be flat, so you get an accurate measurement.

    Adicionar comentário

    • Lay out your new zipper on a flat surface and use the measurement you recorded in the step above, starting from the zipper box, or the bottom of the zipper.

    • Mark the measurement with tailor's chalk.

    • Pull the zipper slider back behind the mark you just made.

    Adicionar comentário

  3. Spread Fixmas Cheer
    Get $12 off your purchase of $50 or more with code FIXMAS12
    Spread Fixmas Cheer
    Get $12 off your purchase of $50 or more with code FIXMAS12
    • Measure one inch beyond where you just marked and make a second mark with tailor’s chalk.

    Adicionar comentário

    • Cut the zipper between the teeth at the second mark you made.

    Adicionar comentário

    • Use end nipper pliers to remove the teeth of the zipper between the two marks.

    • Use needle-nose pliers to remove all the leftover bits of the teeth from the zipper.

    Adicionar comentário

    • Take a zipper stop and align it, posts down, just beyond the last remaining zipper tooth.

    • Crimp the zipper stop onto the zipper using pliers.

    Adicionar comentário

    • Fold the excess zipper tape away from the teeth at a slight angle.

    • Sew the toothless end of the zipper down, backstitching to hold it in place.

    Adicionar comentário

    • Align the toothless edge of the zipper with the inside serged edge of the zipper webbing.

    • The serged edge is the one with the zig-zag stitching.

    • Fold the top of the webbing down over the sewn zipper tape.

    • You can pin the zipper and webbing in place for more stability.

    Adicionar comentário

    • Align the zipper and webbing in the sewing machine so that the zipper teeth are along the edge of the presser foot.

    • Sew a few stitches, removing pins before you come to them.

    Adicionar comentário

    • Sew along the edge of the zipper teeth, making sure that the zipper and webbing stay aligned.

    Adicionar comentário

    • Reinsert the zipper and webbing into the jacket, aligning the edge of the jacket fabric with the zipper teeth.

    Adicionar comentário

    • While holding the zipper in place, move the fabric underneath the zipper out of the way so you’re only sewing the zipper to one layer of fabric.

    Adicionar comentário

    • Install the zipper foot into your sewing machine.

    • Align the jacket and zipper in the sewing machine.

    • Be sure that there is no fabric behind the zipper webbing before you sew.

    Adicionar comentário

    • Check your alignment and begin sewing, guiding the fabric along the zipper teeth.

    • Go slowly, re-aligning the fabric as you go.

    Adicionar comentário

    • Continue sewing and re-aligning the zipper as you proceed along the full length of the zipper.

    Adicionar comentário

    • When you reach the end of the zipper, backstitch to hold your stitches in place and remove the jacket from the sewing machine.

    Adicionar comentário

    • Align the inside jacket fabric along the backside of the webbing.

    • Try to align the stitch holes directly over the stitches you just sewed.

    Adicionar comentário

    • Align the jacket in the sewing machine, with the zipper webbing facing up.

    • Holding the inside fabric of the jack in place, sew directly over the original stitching.

    • Go slowly, re-aligning the fabric as you go.

    • Clip the threads, and admire your work!

    • Repeat this guide, ironing the webbing when you’re finished, to install the other side of the zipper.

    Adicionar comentário

Linha de Chegada

4 outras pessoas concluíram este guia.

Brittany McCrigler

Member since: 05-03-2012

80.050 reputação

132 Guides authored

Equipe

iFixit Membro de iFixit

Community

113 Membros

7.323 Guides authored

Very well documented.

Mike Macey - Responder

Adicionar comentário

Visualizar Estatísticas:

Últimas 24 horas: 28

Últimos 7 dias: 184

Últimos 30 dias: 834

Todo: 28,457