Skip to main content

Introdução

The camera sits on the back of the LCD which can be accessed after removing the logic board.

  1. Place the tablet on a flat clear surface to keep the screen safe. Slide the larger portion of the back cover off the tablet. This will reveal the battery.
    • Place the tablet on a flat clear surface to keep the screen safe.

    • Slide the larger portion of the back cover off the tablet.

    • This will reveal the battery.

  2. Lift the battery out with your finger. Make sure you use the slot near the bottom of the device as shown. Trying to lift from anywhere else will not work and may damage the battery or the device.
    • Lift the battery out with your finger.

    • Make sure you use the slot near the bottom of the device as shown. Trying to lift from anywhere else will not work and may damage the battery or the device.

  3. Using a plastic opening tool, pry off the top cover casing gently by moving the tool along all three sides. Using a plastic opening tool, pry off the top cover casing gently by moving the tool along all three sides.
    • Using a plastic opening tool, pry off the top cover casing gently by moving the tool along all three sides.

  4. Kits de reparo de android

    A new screen or battery is one kit away.

    Comprar agora

    Kits de reparo de android

    A new screen or battery is one kit away.

    Comprar agora
  5. With a T5 hexagonal head, remove the nine black 2.5 mm torx screws. Place them carefully aside on the magnetic mat.
    • With a T5 hexagonal head, remove the nine black 2.5 mm torx screws. Place them carefully aside on the magnetic mat.

  6. Using a plastic opening tool, pry off the back casing gently on each side of the tablet. Using a plastic opening tool, pry off the back casing gently on each side of the tablet. Using a plastic opening tool, pry off the back casing gently on each side of the tablet.
    • Using a plastic opening tool, pry off the back casing gently on each side of the tablet.

  7. Using a Phillips #00 screwdriver, remove the following screws: Four 5mm wide grey Phillips screws on the logic board. One of the 5mm screws is hidden under the circular white tape in the center of the logic board.
    • Using a Phillips #00 screwdriver, remove the following screws:

    • Four 5mm wide grey Phillips screws on the logic board.

    • One of the 5mm screws is hidden under the circular white tape in the center of the logic board.

    • Seven 3mm small grey Phillips screws (four on one side, three on the other) from the black side casing.

  8. Disconnect the five cables connected to the logic board and then carefully lift the logic board out of the casing. Disconnect the five cables connected to the logic board and then carefully lift the logic board out of the casing. Disconnect the five cables connected to the logic board and then carefully lift the logic board out of the casing.
    • Disconnect the five cables connected to the logic board and then carefully lift the logic board out of the casing.

  9. Detach the camera by removing the attached cable. Pulling on the cable may damage the camera if it is still functional; exercise caution. New adhesive may be necessary for the new camera.
    • Detach the camera by removing the attached cable.

    • Pulling on the cable may damage the camera if it is still functional; exercise caution.

    • New adhesive may be necessary for the new camera.

Conclusão

To reassemble your device, follow these instructions in reverse order.

Gregory Philip

Membro desde: 21-09-2016

549 Reputation

4 Guias de autoria

Team

UC Davis, Team 1-1, Oliver Fall 2016 Membro de UC Davis, Team 1-1, Oliver Fall 2016

UCD-OLIVER-F16S1G1

5 Membros

10 Guias de autoria

Add Comment

View Statistics:

Past 24 Hours: 0

Past 7 Days: 0

Past 30 Days: 0

All Time: 167