Conserte seus objetos Comunidade Loja

How to Repair a Broken Speaker Cable on a Harman Kardon CN-04N567-4822

Introdução

Sometimes the moving about of computer speakers leads to broken wires and the speakers will fail to work properly. This guide will show you how to repair a Harman Kardon CN-04N567-48220 external computer speaker.

O que você precisa

  1. How to Repair a Broken Speaker Cable on a Harman Kardon CN-04N567-4822, How to Repair a Broken Speaker Cable on a Harman Kardon CN-04N567-4822: passo 1, imagem 1 %32 How to Repair a Broken Speaker Cable on a Harman Kardon CN-04N567-4822, How to Repair a Broken Speaker Cable on a Harman Kardon CN-04N567-4822: passo 1, imagem 2 %32 How to Repair a Broken Speaker Cable on a Harman Kardon CN-04N567-4822, How to Repair a Broken Speaker Cable on a Harman Kardon CN-04N567-4822: passo 1, imagem 3 %32

    • Use your fingers to pull the top of the speaker grill away from the speaker enclosure.

    • Pull the bottom of the grill away from the speaker enclosure and then completely remove the grill.

    • Four posts attach the grill assembly to the front of speaker enclosure. These posts are located on the back side of the grill assembly.

    Editar

  2. How to Repair a Broken Speaker Cable on a Harman Kardon CN-04N567-4822: passo 2, imagem 1 %32 How to Repair a Broken Speaker Cable on a Harman Kardon CN-04N567-4822: passo 2, imagem 2 %32

    • Remove the top two 9.5 mm Phillips #1 screws from the speaker.

    • Remove the two 9.5 mm Phillips #1 screws located below the speaker screws.

    • Slowly work your way around the seam until the two parts of the enclosure are free.

    • More speaker cable slack may be achieved by pulling additional cable through the rear of the case.

    Editar

  3. How to Repair a Broken Speaker Cable on a Harman Kardon CN-04N567-4822: passo 3, imagem 1 %32 How to Repair a Broken Speaker Cable on a Harman Kardon CN-04N567-4822: passo 3, imagem 2 %32

    • Inspect both sides of the printed circuit board (PCB) for any raised traces, off-colored areas, or loose components.

    • This step is to avoid making a mechanical repair (re-soldering the wires to the PCB) on a piece of equipment that also has obvious electrical or mechanical issues.

    Editar

  5. How to Repair a Broken Speaker Cable on a Harman Kardon CN-04N567-4822: passo 4, imagem 1 %32

    • Use desoldering braid and a soldering iron to wick away the old solder and wire remnants from the solder pads and through-holes.

    • Do not leave solder bridges across the pads as this will cause functional issues.

    Editar

  6. How to Repair a Broken Speaker Cable on a Harman Kardon CN-04N567-4822: passo 5, imagem 1 %32 How to Repair a Broken Speaker Cable on a Harman Kardon CN-04N567-4822: passo 5, imagem 2 %32

    • Use wire strippers to remove a small section of insulation from the wires.

    • Use a soldering iron and solder to tin the wires. This prevents the strands from fraying.

    Editar

  7. How to Repair a Broken Speaker Cable on a Harman Kardon CN-04N567-4822: passo 6, imagem 1 %32 How to Repair a Broken Speaker Cable on a Harman Kardon CN-04N567-4822: passo 6, imagem 2 %32

    • Insert the yellow wire into the through-hole marked "R".

    • Insert the bare ground wire into the through-hole marked "G".

    • Insert the white wire into the through-hole marked "L".

    Editar

  8. How to Repair a Broken Speaker Cable on a Harman Kardon CN-04N567-4822: passo 7, imagem 1 %32

    • Use the soldering iron to flow solder between each wire and its solder pad.

    Editar

  9. How to Repair a Broken Speaker Cable on a Harman Kardon CN-04N567-4822: passo 8, imagem 1 %32

    • Reassemble the two parts of the enclosure making sure that the PCB-mounted audio jacks are lined up with the mating holes of the rear enclosure.

    • Route the cable inside the enclosure to avoid stressing the solder joints.

    Editar
Conclusão

To reassemble your device, follow these instructions in reverse order.

8 outras pessoas executaram este guia.

Autor(a)

com 2 outros contribuidores

Ken Gage

Membro desde: 06/09/16

306 Reputação

Autoria de 1 guia

Emblemas: 6

+3 outros emblemas

Equipe

Texas Tech, Team 3-1, Rauch SU 2016 Membro de Texas Tech, Team 3-1, Rauch SU 2016

TTU-RAUCH-SU16S3G1

Membros da 2

Autoria de 3 guias

0 comentários

Adicione um comentário

Exibir estatísticas:

Últimas 24 horas: 2

Últimos 7 dias: 14

Últimos 30 dias: 68

Duração total: 4,346