Conserte seus objetos Comunidade Loja

Hipstreet Titan 2 HD Speaker Replacement

Introdução

Use this guide to replace the speaker. First you'll need to remove the rear cover. This can be a difficult process.

O que você precisa

  1. Hipstreet Titan 2 HD Speaker Replacement, Rear Case: passo 1, imagem 1 %32

    • Using the PH#00 screwdriver, remove the two 0.145 inch Phillips head screws.

    • The screws are located on the bottom face of the device, near the power and volume controls.

    Editar

  2. Hipstreet Titan 2 HD Speaker Replacement: passo 2, imagem 1 %32

    • Place the small suction cup on your screen.

    • Moisturize the bottom of the suction cup to ensure a proper seal.

    • If the screen is cracked, the suction cup may not seal correctly; too much pressure may crack or damage the screen.

    Editar

  3. Hipstreet Titan 2 HD Speaker Replacement: passo 3, imagem 1 %32

    • Insert the plastic opening tool between the screen cover and rear cover of the tablet.

    • Grasp the small suction cup.

    Editar

  4. Hipstreet Titan 2 HD Speaker Replacement: passo 4, imagem 1 %32 Hipstreet Titan 2 HD Speaker Replacement: passo 4, imagem 2 %32

    • Slide the plastic opening tool along device edge to separate the screen cover from the rear cover.

    • Pull upward on the small suction cup handle while sliding the opening tool.

    • When sliding the plastic opening tool, avoid sliding the tool too far into the cover. This could damage the speaker connector on the back cover.

    Editar

  6. Hipstreet Titan 2 HD Speaker Replacement: passo 5, imagem 1 %32 Hipstreet Titan 2 HD Speaker Replacement: passo 5, imagem 2 %32

    • Use the plastic opening tool to remove the speaker from the rear cover.

    • The speaker is held in place with adhesive and is easily removed.

    • Do not pull on the speaker wires. This could damage the soldering connections.

    Editar

  7. Hipstreet Titan 2 HD Speaker Replacement: passo 6, imagem 1 %32

    • Once the speaker is disconnected, the cover removal is complete.

    Editar

  8. Hipstreet Titan 2 HD Speaker Replacement, Speaker: passo 7, imagem 1 %32

    • Remove the black placement tape.

    Editar

  9. Hipstreet Titan 2 HD Speaker Replacement: passo 8, imagem 1 %32

    • Using a #PH000 screwdriver, remove the three 0.145in circuit board placement screws.

    Editar

  10. Hipstreet Titan 2 HD Speaker Replacement: passo 9, imagem 1 %32 Hipstreet Titan 2 HD Speaker Replacement: passo 9, imagem 2 %32 Hipstreet Titan 2 HD Speaker Replacement: passo 9, imagem 3 %32

    • Lift the hinge locks on the three ribbon connectors and disconnect the ribbon connectors.

    Editar

  11. Hipstreet Titan 2 HD Speaker Replacement: passo 10, imagem 1 %32

    • Identify the two soldered connectors for the speaker.

    Editar

  12. Hipstreet Titan 2 HD Speaker Replacement: passo 11, imagem 1 %32

    • Using a solder removal tool, remove the speaker soldered connectors.

    • Solder the new speaker wire connections to circuit board.

    • First solder the red wire on the left, then the black wire on the right.

    • Solder can burn you. Use caution.

    Editar
Conclusão

To reassemble your device, follow these instructions in reverse order.

2 outras pessoas executaram este guia.

Autor(a)

com 7 outros contribuidores

Jeffrey

Membro desde: 03/11/15

766 Reputação

Autoria de 5 guias

Emblemas: 10

+7 outros emblemas

Equipe

Colorado Springs, Team 5-6, Panko Spring 2015 Membro de Colorado Springs, Team 5-6, Panko Spring 2015

UCCS-PANKO-S15S5G6

3 Membros

Autoria de 10 guias

0 comentários

Comentar

Exibir estatísticas:

Últimas 24 horas: 0

Últimos 7 dias: 0

Últimos 30 dias: 0

Ao todo: 353