Introdução

The purpose of this guide is to instruct the reader on how to replace the faceplates of their HP iPAQ H2200 device.

Peças

Não são necessárias peças.

Press and slide the battery cover tab to remove battery cover.
  • Press and slide the battery cover tab to remove battery cover.

Adicionar comentário

Pull on the black tab to lift the battery out of the battery compartment. Pull on the black tab to lift the battery out of the battery compartment.
  • Pull on the black tab to lift the battery out of the battery compartment.

Adicionar comentário

Remove the stylus by sliding it out of the slot.
  • Remove the stylus by sliding it out of the slot.

Adicionar comentário

Remove the CF card by sliding it out of the slot at the top of the device.
  • Remove the CF card by sliding it out of the slot at the top of the device.

Adicionar comentário

Press down and push the black side strips toward the top of the device to remove them.
  • Press down and push the black side strips toward the top of the device to remove them.

Adicionar comentário

Guia de Presente para o Dia dos Pais
Vamos honrar mais do que nossos pais. Vamos celebrar todos os mentores que nos ensinaram a consertar.
Guia de Presente para o Dia dos Pais
Vamos honrar aqueles que nos ensinaram a consertar.
Using the T5 Torx screwdriver,  remove all six screws on the back and all screws on each side of the device. Using the T5 Torx screwdriver,  remove all six screws on the back and all screws on each side of the device. Using the T5 Torx screwdriver,  remove all six screws on the back and all screws on each side of the device.
  • Using the T5 Torx screwdriver, remove all six screws on the back and all screws on each side of the device.

Adicionar comentário

Remove the back faceplate by pushing and loosening the 4 side slots (2 on each side). Remove the back faceplate by pushing and loosening the 4 side slots (2 on each side).
  • Remove the back faceplate by pushing and loosening the 4 side slots (2 on each side).

Adicionar comentário

Open the LCD connector, where the orange strip attaches to the main board.
  • Open the LCD connector, where the orange strip attaches to the main board.

Adicionar comentário

Carefully remove the orange LCD strip from the connector.
  • Carefully remove the orange LCD strip from the connector.

Adicionar comentário

Unscrew the 2 screws located at each top corner of the main board.
  • Unscrew the 2 screws located at each top corner of the main board.

Adicionar comentário

Remove the main board by pushing outward on the two tabs located on each side near the bottom of the device.
  • Remove the main board by pushing outward on the two tabs located on each side near the bottom of the device.

Adicionar comentário

Unscrew the two bottom screws on LCD screen that were previously located under the main board.
  • Unscrew the two bottom screws on LCD screen that were previously located under the main board.

Adicionar comentário

Press on side tabs to loosen and remove the LCD screen. Press on side tabs to loosen and remove the LCD screen.
  • Press on side tabs to loosen and remove the LCD screen.

Adicionar comentário

Remove the faceplate by unscrewing the green screw located on the top right of the front faceplate.
  • Remove the faceplate by unscrewing the green screw located on the top right of the front faceplate.

Adicionar comentário

Conclusão

To reassemble your device, follow these instructions in reverse order.

Tyler Andrews

Member since: 13-01-2010

191 reputação

5 Guides authored

Equipe

Cal Poly, Team 4-12, Forte Winter 2010 Membro de Cal Poly, Team 4-12, Forte Winter 2010

CPSU-FORTE-W10S4G12

3 Membros

5 Guides authored

Adicionar comentário

Visualizar Estatísticas:

Últimas 24 horas: 1

Últimos 7 dias: 2

Últimos 30 dias: 3

Todo: 1,274