Ir para o conteúdo principal

Esta versão pode conter edições incorretas. Mude para o último instantâneo verificado.

O que você precisa

  1. Este passo não foi traduzido. Ajude a traduzi-lo

    : passo 1, imagem 1 %32 : passo 1, imagem 2 %32
    • Shut down your laptop completely.

    • Do not simply power off your computer using the power button. This will put the laptop into sleep mode. Instead, shut down the laptop from the start menu.

    • Unplug the charger cord and all devices connected to the computer.

  2. Este passo não foi traduzido. Ajude a traduzi-lo

    : passo 2, imagem 1 %32 : passo 2, imagem 2 %32 : passo 2, imagem 3 %32
    • Flip the laptop over and locate the battery compartment release latch.

    • Slide the release latch to the left to release the battery.

  3. Este passo não foi traduzido. Ajude a traduzi-lo

    : passo 3, imagem 1 %32 : passo 3, imagem 2 %32
    • Remove the battery.

  4. Este passo não foi traduzido. Ajude a traduzi-lo

    : passo 4, imagem 1 %32
    • Electrostatic shocks can damage the internal components of the computer.

    • Press and hold the power button for a minimum of 10 seconds to allow electric charge to dissipate from the motherboard and internal components.

    • Optional: You may also wear an anti-static bracelet during the repair as a safety precaution. This grounds you to the computer chassis and prevents accidental static discharge from your fingers.

  5. Este passo não foi traduzido. Ajude a traduzi-lo

    : passo 5, imagem 1 %32
    • Locate and loosen the 3 Phillips PM 2.5 x 11.0 screws on the bottom side of the computer.

  6. Este passo não foi traduzido. Ajude a traduzi-lo

    : passo 6, imagem 1 %32 : passo 6, imagem 2 %32 : passo 6, imagem 3 %32
    • Flip the laptop right side up and open the screen.

    • Locate the 4 keyboard tabs. Slide the tabs towards you.

  7. Este passo não foi traduzido. Ajude a traduzi-lo

    : passo 7, imagem 1 %32 : passo 7, imagem 2 %32 : passo 7, imagem 3 %32
    • Lift the keyboard by the upper edge, then flip it over so the ribbon cable is exposed.

    • Do not attempt to remove the keyboard until the ribbon cable has been disconnected.

  8. Este passo não foi traduzido. Ajude a traduzi-lo

    : passo 8, imagem 1 %32 : passo 8, imagem 2 %32 : passo 8, imagem 3 %32
    • Lift both ends of the plastic tab securing the ribbon cable to the system board with the help of a spudger.

    • If you don't have a spudger, any plastic item with a thin edge, like the plastic opening tool pictured here, will work just as well. Guitar picks are also a good alternative.

  9. Este passo não foi traduzido. Ajude a traduzi-lo

    : passo 9, imagem 1 %32
    • Remove the keyboard ribbon cable and set the keyboard aside.

  10. Este passo não foi traduzido. Ajude a traduzi-lo

    : passo 10, imagem 1 %32
    • Close the laptop and turn it upside down.

    • Remove the 3 PM 2.0 x 3.0 screws securing the switch cover.

  11. Este passo não foi traduzido. Ajude a traduzi-lo

    : passo 11, imagem 1 %32 : passo 11, imagem 2 %32
    • Flip the laptop right side up, and open the display.

    • Locate the LED board ribbon cable. Lift both ends of the plastic tab securing the ribbon cable to the system board.

    • Slide out the LED board ribbon cable.

  12. Este passo não foi traduzido. Ajude a traduzi-lo

    : passo 12, imagem 1 %32 : passo 12, imagem 2 %32 : passo 12, imagem 3 %32
    • Remove the switch cover.

    • You may need to use the spudger or opening tool to pry open the switch cover. It is easiest to start from the top edge, closest to the screen.

  13. Este passo não foi traduzido. Ajude a traduzi-lo

    : passo 13, imagem 1 %32 : passo 13, imagem 2 %32 : passo 13, imagem 3 %32
    • Locate and loosen the 2 slotted Torx T8M 2.5 x 7.0 screws securing the fan to the motherboard.

    • Disconnect the fan cable from the board.

  14. Este passo não foi traduzido. Ajude a traduzi-lo

    : passo 14, imagem 1 %32 : passo 14, imagem 2 %32
    • Lift out vent fan.

    • Clean the dust from the fan with a small brush and/or compressed air.

    • When using compressed air, avoid tilting the bottle greater than 40 degrees from vertical. Doing so will cause the part and your hand to rapidly cool.

  15. Este passo não foi traduzido. Ajude a traduzi-lo

    : passo 15, imagem 1 %32 : passo 15, imagem 2 %32 : passo 15, imagem 3 %32
    • Locate and loosen the 4 Phillips PM 2.5 x 9.0 screws securing the heat sink.

    • You may wish to disconnect the cable adjacent to the heat sink, to make removal easier.

  16. Este passo não foi traduzido. Ajude a traduzi-lo

    : passo 16, imagem 1 %32 : passo 16, imagem 2 %32 : passo 16, imagem 3 %32
    • The thermal paste may have stuck the heat sink to the motherboard. Gently jimmy the heat sink back and forth until it is loose.

    • Extract the heat sink.

  17. Este passo não foi traduzido. Ajude a traduzi-lo

    : passo 17, imagem 1 %32 : passo 17, imagem 2 %32 : passo 17, imagem 3 %32
    • Remove dust trapped in the heat sink vent with compressed air and/or a small brush.

  18. Este passo não foi traduzido. Ajude a traduzi-lo

    : passo 18, imagem 1 %32 : passo 18, imagem 2 %32
    • Remove the old thermal paste from the heat sink and the CPU with a lint free wipe or cotton swab dipped in rubbing alcohol.

  19. Este passo não foi traduzido. Ajude a traduzi-lo

    : passo 19, imagem 1 %32 : passo 19, imagem 2 %32
    • Allow the rubbing alcohol to dry completely.

    • Squeeze a small quantity of thermal paste onto the component's surface. The gobs should be about the size of a grain of rice.

  20. Este passo não foi traduzido. Ajude a traduzi-lo

    : passo 20, imagem 1 %32 : passo 20, imagem 2 %32 : passo 20, imagem 3 %32
    • Reinsert the heat sink into the laptop. Tighten the screws to secure it into place.

Linha de Chegada

24 outras pessoas executaram este guia.

Carolyn Teng

Membro desde: 02/24/15

931 Reputação

Autoria de 1 guia

Equipe

Cal Poly, Team 23-4, Green Winter 2015 Membro de Cal Poly, Team 23-4, Green Winter 2015

CPSU-GREEN-W15S23G4

Membros da 7

Autoria de 15 guias

5 comentários

I didn't think i would find a guide for my 6540b let alone the exact procedure I need. Thanks a million!

tech4eleven - Responder

Awesome tutorial! Cleaned mine pretty quick.

Dawn Eckel - Responder

Your instructions are very helpful. Thank you

Stanford Kaswera - Responder

I have cleaned it all and all went well but on start up I have a blank screen.

Any help?

Fred Paul - Responder

Fred Paul try re seating or replacing ram.Also check .LCD ribbon cable.

Michael - Responder

Adicione um comentário

Exibir estatísticas:

Últimas 24 horas: 2

Últimos 7 dias: 6

Últimos 30 dias: 37

Duração total: 15,656