Introdução

This guide will explain how to replace the primary fans of the device. There is another fan located in the northern section of the interior of the device that this repair guide will not cover. This guide deals with the more involved sections of the device.

Push up on the arrow-shaped switch.
  • Push up on the arrow-shaped switch.

Adicionar comentário

While still holding the  switch up, remove the battery. While still holding the  switch up, remove the battery.
  • While still holding the switch up, remove the battery.

Adicionar comentário

Remove the two  5mm Phillips #0 screws from the hinges Remove the two  5mm Phillips #0 screws from the hinges Remove the two  5mm Phillips #0 screws from the hinges
  • Remove the two 5mm Phillips #0 screws from the hinges

Adicionar comentário

Open the device as if you were going to use the device. Using Tweezers, pry the hinges from underneath the screen Not much force is needed to pull the hinges off once the tweezers are properly positioned
  • Open the device as if you were going to use the device. Using Tweezers, pry the hinges from underneath the screen

  • Not much force is needed to pull the hinges off once the tweezers are properly positioned

Adicionar comentário

Remove the wire connection by gently pulling  on the fuse and connection itself. Do not pull on the wires, as this can remove the wires from the connection, destroying the fuse.
  • Remove the wire connection by gently pulling on the fuse and connection itself.

  • Do not pull on the wires, as this can remove the wires from the connection, destroying the fuse.

Adicionar comentário

Remove the four 4.0 mm Phillips #0 connecting the keyboard to the frame Remove the four 4.0 mm Phillips #0 connecting the keyboard to the frame Remove the four 4.0 mm Phillips #0 connecting the keyboard to the frame
  • Remove the four 4.0 mm Phillips #0 connecting the keyboard to the frame

Adicionar comentário

Gently lift the keyboard up from the frame so that you can see the  ribbon  still connected. Gently lift the keyboard up from the frame so that you can see the  ribbon  still connected.
  • Gently lift the keyboard up from the frame so that you can see the ribbon still connected.

Adicionar comentário

Remove the ribbon by  gently  pulling up the ends of the white receiver it is inserted in to. You may need to use tweezers for this part. During reassembly, when inserting the ribbon, you will hear a quiet, clicking sound when pushing down on the ends of the receiver.  Hearing this ensures the ribbon is in place.
  • Remove the ribbon by gently pulling up the ends of the white receiver it is inserted in to.

  • You may need to use tweezers for this part.

  • During reassembly, when inserting the ribbon, you will hear a quiet, clicking sound when pushing down on the ends of the receiver. Hearing this ensures the ribbon is in place.

Adicionar comentário

Remove  sixteen 5.0 mm Phillips #1 screws from the underside of the device
  • Remove sixteen 5.0 mm Phillips #1 screws from the underside of the device

Adicionar comentário

Remove the one 5.0 mm Phillips #1 screw underneath the battery home
  • Remove the one 5.0 mm Phillips #1 screw underneath the battery home

Adicionar comentário

Remove the additional four 5.0 mm Phillips #1 screws from the hinge of the device Remove the additional four 5.0 mm Phillips #1 screws from the hinge of the device Remove the additional four 5.0 mm Phillips #1 screws from the hinge of the device
  • Remove the additional four 5.0 mm Phillips #1 screws from the hinge of the device

Adicionar comentário

Remove the two 4.0 mm Phillips #0 screws attached to the cicuit board above the keyboard Remove the two 4.0 mm Phillips #0 screws attached to the cicuit board above the keyboard
  • Remove the two 4.0 mm Phillips #0 screws attached to the cicuit board above the keyboard

Adicionar comentário

Gently remove the disconnection to the right of the circuit board
  • Gently remove the disconnection to the right of the circuit board

Adicionar comentário

Take the circuit board off by pulling up on the right side of the circuit board The board is plugged in to the device at this location still, but the outlet is hidden.
  • Take the circuit board off by pulling up on the right side of the circuit board

  • The board is plugged in to the device at this location still, but the outlet is hidden.

  • Pulling on the right side can snap the circuit board, so it is essential you pull on this side only

Adicionar comentário

Remove the five 5.0 mm  Phillips #1 screws from underneath the keyboard Remove the five 5.0 mm  Phillips #1 screws from underneath the keyboard
  • Remove the five 5.0 mm Phillips #1 screws from underneath the keyboard

Adicionar comentário

Disconnect the ribbons from the circuit board underneath the keyboard housing unit Disconnect the ribbons from the circuit board underneath the keyboard housing unit Disconnect the ribbons from the circuit board underneath the keyboard housing unit
  • Disconnect the ribbons from the circuit board underneath the keyboard housing unit

Adicionar comentário

Remove the connection beneath the left hinge of the device Remove the connection beneath the left hinge of the device Remove the connection beneath the left hinge of the device
  • Remove the connection beneath the left hinge of the device

Adicionar comentário

Pry the device apart to expose the inside of the device This should be relatively easy since all connections and screws are removed.  However, a spudger can be used if you are having difficulties.
  • Pry the device apart to expose the inside of the device

  • This should be relatively easy since all connections and screws are removed. However, a spudger can be used if you are having difficulties.

Adicionar comentário

Remove the latches securing the fan housing unit by unscrewing the six 4.0 mm Phillips #0 screws Remove the latches securing the fan housing unit by unscrewing the six 4.0 mm Phillips #0 screws Remove the latches securing the fan housing unit by unscrewing the six 4.0 mm Phillips #0 screws
  • Remove the latches securing the fan housing unit by unscrewing the six 4.0 mm Phillips #0 screws

Adicionar comentário

Lift the housing unit a few inches from the device to expose the two small connections.
  • Lift the housing unit a few inches from the device to expose the two small connections.

Adicionar comentário

Remove the two small connections directly above and below the fan housing unit Remove the two small connections directly above and below the fan housing unit
  • Remove the two small connections directly above and below the fan housing unit

Adicionar comentário

Remove the fan housing unit and flip it over Remove the fan housing unit and flip it over
  • Remove the fan housing unit and flip it over

Adicionar comentário

Remove the eight 3.5 mm Phillips #00 screws from the fan housing unit Remove the eight 3.5 mm Phillips #00 screws from the fan housing unit Remove the eight 3.5 mm Phillips #00 screws from the fan housing unit
  • Remove the eight 3.5 mm Phillips #00 screws from the fan housing unit

Adicionar comentário

Remove both or whichever fan needs to be replaced There  should be bronze electric tape on the fan housing unit.  Do not hesitate to tear the tape in order to open the housing unit
  • Remove both or whichever fan needs to be replaced

  • There should be bronze electric tape on the fan housing unit. Do not hesitate to tear the tape in order to open the housing unit

Adicionar comentário

Conclusão

To reassemble your device, follow these instructions in reverse order.

Eric Beaudry

Member since: 06-03-2018

727 reputação

3 Guides authored

Equipe

Adicionar comentário

Visualizar Estatísticas:

Últimas 24 horas: 0

Últimos 7 dias: 0

Últimos 30 dias: 3

Todo: 26