Introdução

The speaker in your printer could wear out and stop working. This guide will show how to replace the speaker if it stops working. This process will require soldering skills because unplugging the speaker from the control board is a very difficult process.

Lift the hood of the printer. Lift the hood of the printer. Lift the hood of the printer.
  • Lift the hood of the printer.

Adicionar comentário

Remove the two T10 11mm screws. Remove the two T10 11mm screws. Remove the two T10 11mm screws.
  • Remove the two T10 11mm screws.

Adicionar comentário

Remove the panels covering the power brick and cord. Remove the panels covering the power brick and cord. Remove the panels covering the power brick and cord.
  • Remove the panels covering the power brick and cord.

Adicionar comentário

Remove the cord from the power supply. Remove the cord from the power supply.
  • Remove the cord from the power supply.

Adicionar comentário

Slide the power supply out from the chassis. The power supply is still attached; don't pull too quickly. The power supply is still attached; don't pull too quickly.
  • Slide the power supply out from the chassis.

  • The power supply is still attached; don't pull too quickly.

Adicionar comentário

Remove final cable from power supply.
  • Remove final cable from power supply.

Adicionar comentário

There is a hidden screw underneath the model sticker on the front panel. Peel the model sticker off the cover. This will expose the T10 screw securing the panel.
  • There is a hidden screw underneath the model sticker on the front panel.

  • Peel the model sticker off the cover.

  • This will expose the T10 screw securing the panel.

Adicionar comentário

Remove the single 12mm-T10 screw securing the front panel to the printer body. Loosen the panel cover from the printer body. There is a ribbon cable connected to the backside of the cover. Disconnect the cable before separating the panel completely.
  • Remove the single 12mm-T10 screw securing the front panel to the printer body.

  • Loosen the panel cover from the printer body.

  • There is a ribbon cable connected to the backside of the cover. Disconnect the cable before separating the panel completely.

Adicionar comentário

Gently remove the No-Fuss ribbon cable from the front panel. Gently remove the No-Fuss ribbon cable from the front panel. Gently remove the No-Fuss ribbon cable from the front panel.
  • Gently remove the No-Fuss ribbon cable from the front panel.

Adicionar comentário

Remove the seven 8mm screws using the Torx T6 screwdriver. Remove the motherboard from the front-panel housing. The LCD display is on the opposite side.
  • Remove the seven 8mm screws using the Torx T6 screwdriver.

  • Remove the motherboard from the front-panel housing.

  • The LCD display is on the opposite side.

Adicionar comentário

Remove the clip that keeps the printer lid from opening all the way with your hands by pulling away from the post on the lid. Remove the clip that keeps the printer lid from opening all the way with your hands by pulling away from the post on the lid.
  • Remove the clip that keeps the printer lid from opening all the way with your hands by pulling away from the post on the lid.

Adicionar comentário

Remove the paper feed rollers by using your fingers to pinch the indentations together while pulling up. Remove the paper feed rollers by using your fingers to pinch the indentations together while pulling up. Remove the paper feed rollers by using your fingers to pinch the indentations together while pulling up.
  • Remove the paper feed rollers by using your fingers to pinch the indentations together while pulling up.

Adicionar comentário

Remove the ten 11mm-T10 screws with the screwdriver. The top half of the printer might fall open as you remove the screws closer to the hinges.
  • Remove the ten 11mm-T10 screws with the screwdriver.

  • The top half of the printer might fall open as you remove the screws closer to the hinges.

Adicionar comentário

Push the clip holding the speaker in away from the speaker while pulling up  on the speaker. At this point you must cut and solder on your new  speaker. At this point you must cut and solder on your new  speaker.
  • Push the clip holding the speaker in away from the speaker while pulling up on the speaker.

  • At this point you must cut and solder on your new speaker.

Adicionar comentário

Conclusão

To reassemble your device, follow these instructions in reverse order.

Tyler Allen

Member since: 24-01-2018

324 reputação

2 Guides authored

Equipe

Cal Poly, Team S18-G3, Livingston Winter 2018 Membro de Cal Poly, Team S18-G3, Livingston Winter 2018

CPSU-LIVINGSTON-W18S18G3

4 Membros

7 Guides authored

Adicionar comentário

Visualizar Estatísticas:

Últimas 24 horas: 0

Últimos 7 dias: 5

Últimos 30 dias: 18

Todo: 49