Pular para o conteúdo principal

Introdução

Displays can get easily damaged either with time, or with any liquids or impacts.

  1. Ensure the laptop is completely powered off and power adapter is unplugged before removing the battery.
    • Ensure the laptop is completely powered off and power adapter is unplugged before removing the battery.

    • Turn over laptop so that the bottom is showing.

    • Unlock the latch.

  2. Remove the back cover and you will then be able to see the battery.
    • Remove the back cover and you will then be able to see the battery.

  3. Unlatch the two latches securing the battery in the case.
    • Unlatch the two latches securing the battery in the case.

  4. Use the blue opening tool to lift and remove the battery.
    • Use the blue opening tool to lift and remove the battery.

  5. Remove the hard drive by unscrewing the four 8mm screws with the T7 philip's head.
    • Remove the hard drive by unscrewing the four 8mm screws with the T7 philip's head.

  6. Pry off ten rubber paddings on the outer edge of the laptop to reveal the torx screws.
    • Pry off ten rubber paddings on the outer edge of the laptop to reveal the torx screws.

    • Unscrew the ten 8mm torx screws that are under the rubber paddings using the T7 tip torx screwdriver.

  7. Remove the two 4mm screws indicated by the M2.5X4 using the J00 tip screwdriver.
    • Remove the two 4mm screws indicated by the M2.5X4 using the J00 tip screwdriver.

    • Remove SD card cap by just sliding out to reveal one screw.

  8. PC Laptop Batteries

    An easy fix for a big power boost.

    Comprar agora

    PC Laptop Batteries

    An easy fix for a big power boost.

    Comprar agora
  9. Remove the two 3mm screws indicated by the M2.03 using the J00 tip screwdriver.
    • Remove the two 3mm screws indicated by the M2.03 using the J00 tip screwdriver.

    • Remove the 4mm SD card screw using the J00 tip.

  10. Remove the one 4mm fan screw using the J00 tip screwdriver.
    • Remove the one 4mm fan screw using the J00 tip screwdriver.

    • Remove screw and metal plate to expose ribbon cable connector.

  11. Use an opening tool to pry up the ribbon connector to disconnect.
    • Use an opening tool to pry up the ribbon connector to disconnect.

  12. Turn laptop over back to normal position as shown in the image.
    • Turn laptop over back to normal position as shown in the image.

    • Use opening tools to pry up keyboard.

    • When prying up keyboard, be sure to start near any corner of the keyboard.

    • There are two ribbon cables that must be disconnected before fully removing keyboard.

  13. Carefully lift keyboard on one side to expose the two ribbon cables. Use an opening tool to lift up the locking clip and unplug the two ribbon cables. Use an opening tool to lift up the locking clip and unplug the two ribbon cables.
    • Carefully lift keyboard on one side to expose the two ribbon cables.

    • Use an opening tool to lift up the locking clip and unplug the two ribbon cables.

  14. Remove the two 4mm screws centered notated by the keyboard logo using the J00 tip.
    • Remove the two 4mm screws centered notated by the keyboard logo using the J00 tip.

  15. Once keyboard has been fully removed, the system case containing the motherboard can be lifted out easily. The display is connected to the shell of the laptop. The display is connected to the shell of the laptop.
    • Once keyboard has been fully removed, the system case containing the motherboard can be lifted out easily.

    • The display is connected to the shell of the laptop.

  16. Unplug fan cable by pulling away from its connector.
    • Unplug fan cable by pulling away from its connector.

  17. Unscrew the two 6mm fan screws using the J00 tip.
    • Unscrew the two 6mm fan screws using the J00 tip.

    • Fan screws are encased in springs and cannot be removed.

  18. Retrieve the monitor display connected to the plastic chassis.
    • Retrieve the monitor display connected to the plastic chassis.

  19. Unscrew the two 4mm hinge screws using the Philips 00 tip screwdriver.
    • Unscrew the two 4mm hinge screws using the Philips 00 tip screwdriver.

  20. Unhinge the monitor display from the chassis.
    • Unhinge the monitor display from the chassis.

Conclusão

To reassemble your device, follow these instructions in reverse order.

Alberto Carlos Perez

Membro desde: 14-02-2018

314 reputação

2 Guias de autoria

Equipe

USF Tampa, Team S5-G1, Eyestone Spring 2018 Membro de USF Tampa, Team S5-G1, Eyestone Spring 2018

USFT-EYESTONE-S18S5G1

4 Membros

8 Guias de autoria

Adicionar comentário

Visualizar Estatísticas:

Últimas 24 horas: 0

Últimos 7 dias: 11

Últimos 30 dias: 70

Todo: 823