Introdução

Without the scanner glass pane, your printer cannot complete two of its three major functions. Replace a broken one to keep your printer fully-functional.

Peças

Não são necessárias peças.

Take all paper out of the paper tray. Unplug the printer.
  • Take all paper out of the paper tray. Unplug the printer.

  • Remove the plastic printer-control panel on the top left.

  • Then, forcefully lift up the bottom of the panel while applying downward pressure with your thumb-as shown.

Adicionar comentário

With your other hand, slide the top of the panel towards the back of the printer. Do not rip the white cable that connects the panel with the main body of the printer.
  • With your other hand, slide the top of the panel towards the back of the printer.

  • Do not rip the white cable that connects the panel with the main body of the printer.

  • Disconnect the ribbon by pinching the blue tab and pulling away from the green circuit board.

  • Lift the panel free and set to the side.

Adicionar comentário

Place the plastic opening tool between the plastic cover and the mount on the printer.
  • Place the plastic opening tool between the plastic cover and the mount on the printer.

  • Pry the plastic cover towards the center of the printer.

  • Pull up on the cover to remove it from the printer-as shown.

  • Repeat the process on the other side.

Adicionar comentário

Guia de Presente para o Dia dos Pais
Vamos honrar mais do que nossos pais. Vamos celebrar todos os mentores que nos ensinaram a consertar.
Guia de Presente para o Dia dos Pais
Vamos honrar aqueles que nos ensinaram a consertar.
To remove the glass panel, take out the four 14 mm (1/2 inch) screws with a T10 Torx screwdriver.
  • To remove the glass panel, take out the four 14 mm (1/2 inch) screws with a T10 Torx screwdriver.

  • Don't lift the glass panel completely off because there are cables plugged into the underside.

Adicionar comentário

Disconnect the white cables from the green motherboard by pinching the cable where it connects to the green motherboard. Pull up, lightly. Set the lower part of the printer aside. Set the lower part of the printer aside.
  • Disconnect the white cables from the green motherboard by pinching the cable where it connects to the green motherboard. Pull up, lightly.

  • Set the lower part of the printer aside.

Adicionar comentário

Place the glass panel, face down, on a smooth surface. Remove the 14 mm (1/2 in.) screw from the white plastic tab on the side of the panel with a T10 Torx screwdriver.
  • Place the glass panel, face down, on a smooth surface.

  • Remove the 14 mm (1/2 in.) screw from the white plastic tab on the side of the panel with a T10 Torx screwdriver.

Adicionar comentário

Remove the glass pane by carefully bending the plastic frame down from the side and sliding the glass pane out from the side. Remove the glass pane by carefully bending the plastic frame down from the side and sliding the glass pane out from the side. Remove the glass pane by carefully bending the plastic frame down from the side and sliding the glass pane out from the side.
  • Remove the glass pane by carefully bending the plastic frame down from the side and sliding the glass pane out from the side.

Adicionar comentário

Conclusão

To reassemble your device, follow these instructions in reverse order.

Uma outra pessoa concluiu este guia.

Samuel Isbell

Member since: 09-10-2012

10 reputação

Autoria de 1 guia

Equipe

Cal Poly, Team 9-18, Amido Fall 2012 Membro de Cal Poly, Team 9-18, Amido Fall 2012

CPSU-AMIDO-F12S9G18

4 Membros

5 Guides authored

Adicionar comentário

Visualizar Estatísticas:

Últimas 24 horas: 4

Últimos 7 dias: 9

Últimos 30 dias: 26

Todo: 2,688