Introdução

This guide shows the user how to properly remove the RAM from the Gateway MS2370 Laptop.

Peças

Não são necessárias peças.

Make sure the laptop is turned off and  flipped over so that the bottom is facing up. Then, locate the battery clip as shown.
  • Make sure the laptop is turned off and flipped over so that the bottom is facing up. Then, locate the battery clip as shown.

Adicionar comentário

Either using your fingers or a plastic spudger push the battery clip to the left to release battery.
  • Either using your fingers or a plastic spudger push the battery clip to the left to release battery.

Adicionar comentário

Pull the battery from the laptop to remove it.
  • Pull the battery from the laptop to remove it.

Adicionar comentário

Unscrew the three 10mm inch Phillips 01 screws on the back of your laptop.
  • Unscrew the three 10mm inch Phillips 01 screws on the back of your laptop.

  • Unplug everything from the USB and SD ports.

Adicionar comentário

Remove the cover panel.
  • Remove the cover panel.

  • This exposes more screws that must be removed.

Adicionar comentário

Unplug the two exposed cables from the motherboard.
  • Unplug the two exposed cables from the motherboard.

Adicionar comentário

Unscrew  the rest of the case screws which include several 10mm 01 Phillips screws and three 3mm 00 Phillips screws. This marked screw will not fully come out. Just loosen it and leave it there it will not effect the rest of the replacement.
  • Unscrew the rest of the case screws which include several 10mm 01 Phillips screws and three 3mm 00 Phillips screws.

  • This marked screw will not fully come out. Just loosen it and leave it there it will not effect the rest of the replacement.

Adicionar comentário

Pry the laptop case apart. The disc drive in this photo was removed.  You can remove it just by puling it out when the previous step is completed.
  • Pry the laptop case apart.

  • The disc drive in this photo was removed. You can remove it just by puling it out when the previous step is completed.

Adicionar comentário

Unplug the track-pad and the keyboard ribbon cable by lifting up the grey flap and removing the cable.
  • Unplug the track-pad and the keyboard ribbon cable by lifting up the grey flap and removing the cable.

  • This cable has a special connector the requires you to lift open a grey flap to unplug properly.

  • The keyboard plug is located at the center of the motherboard and can be unplugged like a normal cable.

Adicionar comentário

Remove the top half of the case.
  • Remove the top half of the case.

Adicionar comentário

Unscrew all  5 10mm inch Phillips 01 screws.
  • Unscrew all 5 10mm inch Phillips 01 screws.

  • One more off screen

Adicionar comentário

Unplug the ribbon cable connected to the USB Hub, the network card, and the monitor cable. Unplug the ribbon cable connected to the USB Hub, the network card, and the monitor cable. Unplug the ribbon cable connected to the USB Hub, the network card, and the monitor cable.
  • Unplug the ribbon cable connected to the USB Hub, the network card, and the monitor cable.

Adicionar comentário

Flip the motherboard over.
  • Flip the motherboard over.

Adicionar comentário

Using your two thumbs to pull outwards from the inside of the RAM slot to release and remove the RAM. The last step of this replacement guide is not required to complete the fan replacement guide. The last step of this replacement guide is not required to complete the fan replacement guide.
  • Using your two thumbs to pull outwards from the inside of the RAM slot to release and remove the RAM.

  • The last step of this replacement guide is not required to complete the fan replacement guide.

Adicionar comentário

Conclusão

To reassemble your device, follow these instructions in reverse order.

Mathieu Bolduc-Clayton

Member since: 17-10-2017

401 reputação

4 Guides authored

Equipe

Adicionar comentário

Visualizar Estatísticas:

Últimas 24 horas: 0

Últimos 7 dias: 1

Últimos 30 dias: 8

Todo: 115