Ir para o conteúdo principal

Introdução

Replacing the battery in the Garmin Nuvi 200

  1. Peel off the sticker from the bottom of the device to reveal two screws. Peel off the sticker from the bottom of the device to reveal two screws.
    • Peel off the sticker from the bottom of the device to reveal two screws.

  2. Remove two T5 Torx screws.
    • Remove two T5 Torx screws.

  3. Insert a plastic opening tool in the gap between the front and rear casing. Carefully work the tool around the gap, separating the two halves of the case.
    • Insert a plastic opening tool in the gap between the front and rear casing.

    • Carefully work the tool around the gap, separating the two halves of the case.

    • Keep the power switch in place while removing the rear case.

  4. Peel away the tape holding the ribbon cable in place.
    • Peel away the tape holding the ribbon cable in place.

    • Disconnect the ribbon cable by using a spudger to flip up the retaining flap on its ZIF-style connector. Then gently remove the cable.

  5. Pull out the cable between the logic board and the speaker to disconnect them.
    • Pull out the cable between the logic board and the speaker to disconnect them.

  6. Remove the three screws from the logic board using the #00 Phillips screwdriver. Lift the board away from the case but do not pull the logic board completely off, as it is still attached to the battery by a cable.
    • Remove the three screws from the logic board using the #00 Phillips screwdriver.

    • Lift the board away from the case but do not pull the logic board completely off, as it is still attached to the battery by a cable.

  7. Detach the logic board form the battery by pulling out the cable. Detach the logic board form the battery by pulling out the cable.
    • Detach the logic board form the battery by pulling out the cable.

  8. Do not use any sharp objects around the battery, as these may puncture the battery. Remove the battery by pulling it away from the casing.
    • Do not use any sharp objects around the battery, as these may puncture the battery.

    • Remove the battery by pulling it away from the casing.

    • The battery is glued to the casing.

Conclusão

To reassemble your device, follow these instructions in reverse order.

14 outras pessoas concluíram este guia.

Anjelica

Membro desde: 11-04-2010

504 Reputation

3 Guias de autoria

Team

Cal Poly, Team 25-90, Amido Spring 2010 Membro de Cal Poly, Team 25-90, Amido Spring 2010

CPSU-AMIDO-S10S25G90

4 Membros

9 Guias de autoria

This document could be improved by including information about where to acquire a replacement battery, and any modifications that might be required to a generic battery.

Jonathan Moore - Responder

Here's the replacement battery needed for the Garmin Nuvi 200. It's brand new, it comes with all the necessary installation tools and it has a 1 year warranty! Garmin Nuvi 200 Replacement Battery

Mike -

Seems like there are some on Amazon and Ebay. Not sure how to verify getting the right one. Not that expensive, so maybe worth the risk.

Jim Carnicom - Responder

It was a huge mistake to peel away the ribbon cable. It needs matched up precisely and exactly in the same alignment as it was before during reassembly, an apparently impossible task once it's been detached. I'd advise opening the halves in book form, leaving the ribbon cable as a hinge. Have about given up trying to position it.

Nice tutorial, except for the booby trap.

gepetto4 - Responder

Cannot stress enough that the step 5 calling for the removal of the tape holding the ribbon cable be removed from this guide! My Nuvi will not work anymore because I can't get that ribbon cable aligned. I wish I had read all the comments as the above poster warned of this very problem. Please update the guide and remove step 5!

Jarrod - Responder

Add Comment

View Statistics:

Past 24 Hours: 4

Past 7 Days: 23

Past 30 Days: 124

All Time: 42,565