Ir para o conteúdo principal

Etekcity Lasergrip 1080 Laser Replacement

O que você precisa

  1. Etekcity Lasergrip 1080 Laser Replacement, Battery: passo 1, imagem 1 %32
    • Pull the battery cover away from the handle by gripping near the thumb groove.

  2. Etekcity Lasergrip 1080 Laser Replacement: passo 2, imagem 1 %32
    • Gently pull the battery out of the handle.

    • Excessive force could damage wires.

  3. Etekcity Lasergrip 1080 Laser Replacement: passo 3, imagem 1 %32 Etekcity Lasergrip 1080 Laser Replacement: passo 3, imagem 2 %32
    • Disconnect the battery by pulling the connector away from it.

    • Positive first

    • Negative second

    • When replacing the battery, this order is reversed.

  4. Etekcity Lasergrip 1080 Laser Replacement, Buttons: passo 4, imagem 1 %32 Etekcity Lasergrip 1080 Laser Replacement, Buttons: passo 4, imagem 2 %32
    • Remove the battery cover from the device by pulling it straight out.

  5. Etekcity Lasergrip 1080 Laser Replacement: passo 5, imagem 1 %32 Etekcity Lasergrip 1080 Laser Replacement: passo 5, imagem 2 %32
    • Using the plastic opening tool remove the front and rear yellow covers.

    • When removing the back cover, be careful not to lose the buttons as they are not connected.

  6. Etekcity Lasergrip 1080 Laser Replacement: passo 6, imagem 1 %32
    • Remove the two 3.1 mm Phillips #0 screws.

  7. Etekcity Lasergrip 1080 Laser Replacement: passo 7, imagem 1 %32 Etekcity Lasergrip 1080 Laser Replacement: passo 7, imagem 2 %32
    • Pull the two halves apart.

    • Be careful not to lose any components on the inside.

  8. Etekcity Lasergrip 1080 Laser Replacement: passo 8, imagem 1 %32
    • Realign the buttons with the button terminals.

    • Red terminal to red button.

    • Orange terminal to orange button.

    • Yellow terminal to yellow button.

  9. Etekcity Lasergrip 1080 Laser Replacement, Etekcity Lasergrip 1080 Trigger Replacement: passo 9, imagem 1 %32 Etekcity Lasergrip 1080 Laser Replacement, Etekcity Lasergrip 1080 Trigger Replacement: passo 9, imagem 2 %32
    • Carefully pull the trigger out.

    • The trigger is spring loaded, so be careful that you do not lose the spring as you pull the trigger out.

    • To put the trigger back in, align the peg with the hole in the handle and align the shaft with the button terminal.

  10. Etekcity Lasergrip 1080 Laser Replacement, Laser: passo 10, imagem 1 %32
    • Pull the motherboard out of its slot in the device.

  11. Etekcity Lasergrip 1080 Laser Replacement: passo 11, imagem 1 %32
    • Use a soldering iron to melt the solder that holds the wires for the laser to the motherboard.

    • Soldering irons are hot and should only be handled by those who know what they are doing and are wearing proper safety equipment. There is a link to a soldering guide in the Troubleshooting section of the device page.

Conclusão

To reassemble your device, follow these instructions in reverse order.

Patrick Crawford

Membro desde: 08/26/15

741 Reputação

Autoria de 6 guias

Equipe

USF Tampa, Team 5-1, Blackwell Fall 2015 Membro de USF Tampa, Team 5-1, Blackwell Fall 2015

USFT-BLACKWELL-F15S5G1

Membros da 3

Autoria de 9 guias

0 comentários

Adicione um comentário

Exibir estatísticas:

Últimas 24 horas: 3

Últimos 7 dias: 5

Últimos 30 dias: 20

Duração total: 890