Introdução

This guide shows how to remove the paper eject frame assembly Constant paper jams might be caused by a faulty paper eject frame assembly. This process requires the knowledge of how to use basic tools.

Turn off the printer.
  • Turn off the printer.

  • Disconnect all data connections coming into the printer such as USB, networkd cables, firewire, etc. as well as removing the power cord.

Adicionar comentário

Locate the IEEE cover in  the back.
  • Locate the IEEE cover in the back.

  • Gently slide cover to the right to unlatch then pull to remove it.

Adicionar comentário

  • Using a #2 Phillips screwdriver, remove the four 10mm screws shown.

  • Remove the 6mm screw that holds the rear housing in place.

Adicionar comentário

  • Remove the rear housing by pulling it backwards.

Adicionar comentário

  • Insert the flathead screwdriver or plastic pry tool into the cutouts of the lower housing.

  • Release the two tabs of the side housing by lifting the tool in an upward motion

  • Remove the side housing by pulling it outwards.

Adicionar comentário

  • Both side housings are attached by the same type of mechanism.

  • Using the same method, remove the other side housing.

Adicionar comentário

  • Lift the paper support.

  • Open the printer cover and front cover.

Adicionar comentário

  • Remove the four 10 mm Phillips #2 screws from the sides of the printer.

  • Remove the three 6mm Phillips #2 screws.

Adicionar comentário

  • Detach the tabs from the pins on each side by pulling it outwards.

Adicionar comentário

  • Remove the two 10 mm Phillips #2 screws on the front of the printer.

Adicionar comentário

  • Disconnect the cable on the side by carefully pulling it outwards.

  • You may need to gently rock the cable up and down while pulling.

Adicionar comentário

  • Remove the upper housing by lifting it upwards.

  • It's easier to lift the housing by gripping it from the bottom.

Adicionar comentário

  • Hold the ink tube and draw out the waste ink tube by pulling on both tubes in opposite directions.

Adicionar comentário

  • Remove the acetate tape that secure the connector cable.

Adicionar comentário

  • There are six screws that secure the printer mechanism.

  • Using the #2 Phillips screwdriver, remove the three 10mm screws shown.

Adicionar comentário

  • Using the #2 Phillips screwdriver, remove the last three 10mm screws securing the printer mechanism.

Adicionar comentário

  • Remove printer mechanism from lower housing by holding the handles and lifting it upwards.

Adicionar comentário

  • Remove the CD-R unit housing by releasing the two attaching points to the tray base.

  • Pull it outwards diagonally one side at a time.

Adicionar comentário

  • Remove the left frame support plate by removing the two 6mm screws that secure it.

  • Pull it out by hand to free it.

Adicionar comentário

  • Using the #2 Phillips screwdriver, remove the four 6mm screws.

  • Remove the two 8mm screws.

  • The screws are located on the lower sections of the printer.

Adicionar comentário

  • Two guide pins secure the paper EJ assy in place.

  • Remove the two guide pins on the CD/DVD tray base by pulling each pin outward.

Adicionar comentário

  • Remove the paper EJ frame assy by pulling the it towards you.

Adicionar comentário

Conclusão

To reassemble your device, follow these instructions in reverse order.

27 outras pessoas concluíram este guia.

Larry Huang

Member since: 12-10-2011

704 reputação

4 Guides authored

Equipe

Cal Poly, Team 17-11, Regan Fall 2011 Membro de Cal Poly, Team 17-11, Regan Fall 2011

CPSU-REGAN-F11S17G11

4 Membros

6 Guides authored

Adicionar comentário

Visualizar Estatísticas:

Últimas 24 horas: 4

Últimos 7 dias: 18

Últimos 30 dias: 104

Todo: 12,077