Conserte seus objetos Comunidade Loja

Electrohome EAAC475 USB Port Replacement

Introdução

Use this guide if your USB devices like smartphones are not charging from the port in your electrohome EAAC475. Also, you can use this guide to replace the port with the new one.

O que você precisa

  1. Electrohome EAAC475 USB Port Replacement, Battery: passo 1, imagem 1 %32 Electrohome EAAC475 USB Port Replacement, Battery: passo 1, imagem 2 %32

    • Remove the 10 mm Phillips #1 screw from the battery cover.

    • Remove the battery cover.

    Editar

  2. Electrohome EAAC475 USB Port Replacement: passo 2, imagem 1 %32

    • Remove the flat lithium battery.

    Editar

  3. Electrohome EAAC475 USB Port Replacement, Buttons: passo 3, imagem 1 %32 Electrohome EAAC475 USB Port Replacement, Buttons: passo 3, imagem 2 %32

    • Disconnect the radio from all power sources.

    • Remove the two 10 mm Phillips #1 screws from the bottom of the device.

    • Remove two 10 mm Phillips #1 screws from the back side of the device.

    Editar

  5. Electrohome EAAC475 USB Port Replacement: passo 4, imagem 1 %32 Electrohome EAAC475 USB Port Replacement: passo 4, imagem 2 %32 Electrohome EAAC475 USB Port Replacement: passo 4, imagem 3 %32

    • Carefully and slowly pull the lower case away from the rest of the device.

    • Do not completely separate the lower case. There are several wires connecting the two halves of the device.

    • Flip the device over to access the button assembly.

    • Slowly remove the button contact board from the assembly.

    Editar

  6. Electrohome EAAC475 USB Port Replacement: passo 5, imagem 1 %32 Electrohome EAAC475 USB Port Replacement: passo 5, imagem 2 %32

    • Remove the two 7 mm Phillips # 1 screws holding the buttons.

    • Remove the plastic buttons.

    Editar

  7. Electrohome EAAC475 USB Port Replacement, USB Port: passo 6, imagem 1 %32

    • Locate the screw holding the USB circuit board in place.

    • Take a Philips head screwdriver and remove the 10 mm screw.

    Editar

  8. Electrohome EAAC475 USB Port Replacement: passo 7, imagem 1 %32

    • Upon removing the screw, the circuit board should slide right out to look like this.

    • The USB port is to the right in this picture.

    Editar

  9. Electrohome EAAC475 USB Port Replacement: passo 8, imagem 1 %32

    • Find the pins of the USB port that are soldered into the circuit board.

    • Compare the new port with the old port to be sure which pins to work with.

    • Take the soldering gun and heat up the pins one at a time.

    • If you are not familiar with soldering, consult a more skilled individual or at least a how-to guide.

    • Use solder wick with each pin to remove the solder.

    • Remove the USB port.

    Editar
Conclusão

To reassemble your device, follow these instructions in reverse order.

Uma outra pessoa concluiu este guia.

Autor(a)

com 3 outros contribuidores

Sterling Fulk

Membro desde: 02/16/16

264 Reputação

Autoria de 2 guias

Emblemas: 12

+9 outros emblemas

Equipe

IUPUI, Team 2-1, Harley Spring 2016 Membro de IUPUI, Team 2-1, Harley Spring 2016

IUPUI-HARLEY-S16S2G1

Membros da 4

Autoria de 6 guias

0 comentários

Adicione um comentário

Exibir estatísticas:

Últimas 24 horas: 0

Últimos 7 dias: 1

Últimos 30 dias: 3

Duração total: 255