Conserte seus objetos Comunidade Loja

Dynex DX-WBRDVD1 Power Supply Board Replacement

Introdução

This guide was made to help people replace a power supply board in a Dynex DX-WBRDVD1 DVD player. The power supply board regulates and supplies power to the connected components in the DVD player that make it operational. Without the DVD power supply board, the DVD player will be unable to operate.

Before starting, make sure to turn off and unplug the DVD player from any external power source.

O que você precisa

  1. Dynex DX-WBRDVD1 Power Supply Board Replacement, Top Cover: passo 1, imagem 1 %32 Dynex DX-WBRDVD1 Power Supply Board Replacement, Top Cover: passo 1, imagem 2 %32

    • Remove the four 5mm Phillips #1 screws that connect the black outer shell to the silver back of the device.

    Editar

  2. Dynex DX-WBRDVD1 Power Supply Board Replacement: passo 2, imagem 1 %32

    • Remove the two 5mm screws on the left and right side panels.

    • There is one screw on each side that secures the cover to the body of the device.

    Editar

  3. Dynex DX-WBRDVD1 Power Supply Board Replacement: passo 3, imagem 1 %32

    • Lift the black cover to a 45 degree angle from the rear of the device and pull the cover away entirely.

    • Check that the power cord is not preventing the device from opening or closing.

    Editar

  5. Dynex DX-WBRDVD1 Power Supply Board Replacement, Power Supply Board: passo 4, imagem 1 %32 Dynex DX-WBRDVD1 Power Supply Board Replacement, Power Supply Board: passo 4, imagem 2 %32

    • Remove the 9-pin white wire from the power board (brown) that connects to the motherboard (green).

    Editar

  6. Dynex DX-WBRDVD1 Power Supply Board Replacement: passo 5, imagem 1 %32 Dynex DX-WBRDVD1 Power Supply Board Replacement: passo 5, imagem 2 %32

    • Remove the front plate of the device by removing the top two screws on either side and pulling the plate away.

    • Make sure to place the grounding wire between the screw and the device when reassembling.

    Editar

  7. Dynex DX-WBRDVD1 Power Supply Board Replacement: passo 6, imagem 1 %32 Dynex DX-WBRDVD1 Power Supply Board Replacement: passo 6, imagem 2 %32

    • Remove the 4 screws holding the power board to the body of the device.

    • Remember to connect a grounding wire to the screw next to the front panel and optical drive when reassembling.

    Editar

  8. Dynex DX-WBRDVD1 Power Supply Board Replacement: passo 7, imagem 1 %32 Dynex DX-WBRDVD1 Power Supply Board Replacement: passo 7, imagem 2 %32

    • Press down on the plastic flap to unlatch the white clip on the edge of the power supply board.

    Editar

  9. Dynex DX-WBRDVD1 Power Supply Board Replacement: passo 8, imagem 1 %32

    • Remove the power supply board.

    Editar
Conclusão

To reassemble your device, follow these instructions in reverse order.

3 outras pessoas executaram este guia.

0 comentários

Adicione um comentário

Exibir estatísticas:

Últimas 24 horas: 1

Últimos 7 dias: 1

Últimos 30 dias: 8

Duração total: 674