Conserte seus objetos Comunidade Loja

Disassembling the Teac DC-D2831

Introdução

This will walk you through the steps necessary to access crucial parts inside the Teac DC-D2831, to make adjustments or repairs. Electronics are delicate, so be sure to take caution when making modifications and during reassembly. Needle nose pliers are a must for removing the snap ring!

Before beginning this repair, turn off your stereo and unplug it from the power outlet.

O que você precisa

  1. Disassembling the Teac DC-D2831, Disassembling the Teac DC-D2831: passo 1, imagem 1 %32

    • Make sure the device is turned off and unplugged. This will eliminate the danger of getting electrocuted while repairing the device or damaging components.

    Editar

  2. Disassembling the Teac DC-D2831: passo 2, imagem 1 %32 Disassembling the Teac DC-D2831: passo 2, imagem 2 %32

    • Lift the lid to get to the turntable.

    • Using the appropriate tools (needle-nose pliers, tweezers, screwdriver, etc.), remove the snap ring from the center of the turntable. The snap-ring is the small metal ring around the axel of the turntable.

    • The snap-ring is hard to remove so be patient and don't be afraid to use some force.

    • Feel free to use whatever tool(s) that will remove the snap-ring. The above list of tools are just a suggestions.

    Editar

  4. Disassembling the Teac DC-D2831: passo 3, imagem 1 %32 Disassembling the Teac DC-D2831: passo 3, imagem 2 %32

    • Gently lift the turntable from the rest of the device.

    • If the device has a faulty belt, see the belt repair guide here: Belt Repair Guide

    Editar

  5. Disassembling the Teac DC-D2831: passo 4, imagem 1 %32

    • Remove the screws on the side of the device using a Phillips #2 screwdriver.

    • When removing the screws, take note of which screws go where.

    • 27.0mm

    • 19.8mm

    • 12.0mm

    Editar

  6. Disassembling the Teac DC-D2831: passo 5, imagem 1 %32 Disassembling the Teac DC-D2831: passo 5, imagem 2 %32

    • Lift the base that the turntable was resting on from the rest of the device.

    • Remove the base slowly so to not sever the connection with the wire attached from the base to the circuit board.

    Editar

  7. Disassembling the Teac DC-D2831: passo 6, imagem 1 %32
    Editar
Conclusão

To reassemble your device, follow these instructions in reverse order.

3 outras pessoas executaram este guia.

Autor(a)

com 6 outros contribuidores

Jake Hamilton

Membro desde: 09/19/12

167 Reputação

Autoria de 2 guias

Emblemas: 11

+8 outros emblemas

Equipe

Cal Poly, Team 2-61, Propen Fall 2012 Membro de Cal Poly, Team 2-61, Propen Fall 2012

CPSU-PROPEN-F12S2G61

Membros da 4

Autoria de 5 guias

2 comentários

How to remove lid from CD-D2831

jfranklinhamm - Responder

So radio sound and tape work and sound is great. However when turn table is on the sound is low only on that component any help would be greatly appreciated

Joanna Chavez - Responder

Adicione um comentário

Exibir estatísticas:

Últimas 24 horas: 0

Últimos 7 dias: 1

Últimos 30 dias: 15

Duração total: 4,664