Introdução

This guide will show you how to remove the main camera lens assembly from the camera's frame.

Peças

Não são necessárias peças.

Remove the following screws: Two silver 3.15mm Phillips #00 screws on the right side of the camera
  • Remove the following screws:

    • Two silver 3.15mm Phillips #00 screws on the right side of the camera

    • Two silver 2.08mm Phillips #00 screws on the left side of the camera

Adicionar comentário

Remove the two indicated screws on the bottom of the camera:
  • Remove the two indicated screws on the bottom of the camera:

    • The screw circled in red is a longer silver 3.15mm Phillips #00 screw

    • The screw circled in blue is a shorter silver 2.25mm Phillips #00 screw

Adicionar comentário

Carefully pull the back of casing away from the front. Carefully pull the back of casing away from the front.
  • Carefully pull the back of casing away from the front.

Adicionar comentário

After removing the back cover, several things must be removed. Silver donut-shaped button will fall off. Place separately. Remove the plug covers on the right side of camera, labeled “PC/AV” and “DC IN 4.5V”. Silver donut-shaped button will fall off. Place separately. Remove the plug covers on the right side of camera, labeled “PC/AV” and “DC IN 4.5V”.
  • After removing the back cover, several things must be removed.

  • Silver donut-shaped button will fall off. Place separately. Remove the plug covers on the right side of camera, labeled “PC/AV” and “DC IN 4.5V”.

Adicionar comentário

To remove the front cover, gently hold the inside structure of the camera and slowly pull the front cover off. To remove the front cover, gently hold the inside structure of the camera and slowly pull the front cover off.
  • To remove the front cover, gently hold the inside structure of the camera and slowly pull the front cover off.

Adicionar comentário

On the front of the camera, in battery case, remove screws indicated: Two black 2.05mm Phillips #00 screws
  • On the front of the camera, in battery case, remove screws indicated:

    • Two black 2.05mm Phillips #00 screws

Adicionar comentário

Flip the camera over to the backside and remove screws indicated: The screw circled in red is a longer black 3.00mm Phillips #00 screw
  • Flip the camera over to the backside and remove screws indicated:

    • The screw circled in red is a longer black 3.00mm Phillips #00 screw

    • The screw circled in red is a shorter black 2.00mm Phillips #00 screw

Adicionar comentário

Pull the cover plate off for the two power cord jacks.
  • Pull the cover plate off for the two power cord jacks.

Adicionar comentário

Cautiously and gently pull up the control board at the upper left corner, next to the viewfinder. Cautiously and gently pull up the control board at the upper left corner, next to the viewfinder. Cautiously and gently pull up the control board at the upper left corner, next to the viewfinder.
  • Cautiously and gently pull up the control board at the upper left corner, next to the viewfinder.

Adicionar comentário

Remove the orange tape on top of the SD cardholder.
  • Remove the orange tape on top of the SD cardholder.

Adicionar comentário

Open the battery cover and lift plastic piece off. Open the battery cover and lift plastic piece off. Open the battery cover and lift plastic piece off.
  • Open the battery cover and lift plastic piece off.

Adicionar comentário

Remove tape on left side of camera.
  • Remove tape on left side of camera.

Adicionar comentário

Remove the indicated 2.40mm Phillips #00 screw to release top left LCD bracket.
  • Remove the indicated 2.40mm Phillips #00 screw to release top left LCD bracket.

Adicionar comentário

Remove top left LCD bracket.
  • Remove top left LCD bracket.

  • This is a small piece, be careful not to lose it.

Adicionar comentário

Push down bottom left LCD bracket to release the LCD from grip. Push down bottom left LCD bracket to release the LCD from grip.
  • Push down bottom left LCD bracket to release the LCD from grip.

Adicionar comentário

Gently lift up LCD screen.
  • Gently lift up LCD screen.

Adicionar comentário

Slowly pull LCD screen to the left to remove it from the other grips. BEWARE: The LCD screen is attached to the logic board by two wires at the bottom. BEWARE: The LCD screen is attached to the logic board by two wires at the bottom.
  • Slowly pull LCD screen to the left to remove it from the other grips.

  • BEWARE: The LCD screen is attached to the logic board by two wires at the bottom.

Adicionar comentário

Lift up tape slightly on both sides of speaker. Lift up tape slightly on both sides of speaker. Lift up tape slightly on both sides of speaker.
  • Lift up tape slightly on both sides of speaker.

Adicionar comentário

Use the pointed end of a spudger to lift up brackets. Lift speaker cover out. Lift speaker cover out.
  • Use the pointed end of a spudger to lift up brackets.

  • Lift speaker cover out.

Adicionar comentário

Remove speaker cover.
  • Remove speaker cover.

Adicionar comentário

Turn camera to front. Carefully peel off orange wire tape. The tape is glued to the surface indicated.
  • Turn camera to front.

  • Carefully peel off orange wire tape. The tape is glued to the surface indicated.

  • Lift speaker from holder.

Adicionar comentário

Use a wedge to lift up the wire tape flap. Use a wedge to lift up the wire tape flap.
  • Use a wedge to lift up the wire tape flap.

Adicionar comentário

Insert the point of a spudger underneath the wire shown. Insert the point of a spudger underneath the wire shown. Insert the point of a spudger underneath the wire shown.
  • Insert the point of a spudger underneath the wire shown.

Adicionar comentário

Carefully lift the wire out of the crevasses. Carefully lift the wire out of the crevasses.
  • Carefully lift the wire out of the crevasses.

Adicionar comentário

Slowly bend the speaker's wire tape away from the lens assembly.  Avoid creasing the tape.
  • Slowly bend the speaker's wire tape away from the lens assembly. Avoid creasing the tape.

Adicionar comentário

Remove indicated screws: Three Black 3.80mm Phillips #00 screws. Three Black 3.80mm Phillips #00 screws.
  • Remove indicated screws:

    • Three Black 3.80mm Phillips #00 screws.

Adicionar comentário

Remove the indicated black 3.40mm Phillips #00 screw on the bottom of the camera. Remove copper leads.
  • Remove the indicated black 3.40mm Phillips #00 screw on the bottom of the camera.

  • Remove copper leads.

Adicionar comentário

Unscrew the indicated 3.80mm Phillips #00 screw on the back of the camera. Remove screw and bracket. Remove screw and bracket.
  • Unscrew the indicated 3.80mm Phillips #00 screw on the back of the camera.

  • Remove screw and bracket.

Adicionar comentário

Turn the camera over to the front.
  • Turn the camera over to the front.

  • In the following step, you will undo the indicated pegs. PROCEED TO THE NEXT STEP.

Adicionar comentário

Carefully holding the camera, grab the corresponding two points. Carefully twist the lens assembly away from you. You will be turning your hand clockwise. Pull lens assembly out.
  • Carefully holding the camera, grab the corresponding two points.

  • Carefully twist the lens assembly away from you. You will be turning your hand clockwise.

  • Pull lens assembly out.

  • The lens assembly is attached to the logic board by wire tape.

Adicionar comentário

Conclusão

To reassemble your device, follow these instructions in reverse order.

Bassem Tossoun

Member since: 21-01-2011

201 reputação

2 Guides authored

Equipe

Cal Poly, Team 4-29, Regan Winter 2011 Membro de Cal Poly, Team 4-29, Regan Winter 2011

CPSU-REGAN-W11S4G29

3 Membros

5 Guides authored

Adicionar comentário

Visualizar Estatísticas:

Últimas 24 horas: 0

Últimos 7 dias: 0

Últimos 30 dias: 4

Todo: 1,475