Ir para o conteúdo principal

Disassembling Palm Centro Logic Board

O que você precisa

  1. Disassembling Palm Centro Logic Board, Disassembling Palm Centro Battery: passo 1, imagem 1 %32 Disassembling Palm Centro Logic Board, Disassembling Palm Centro Battery: passo 1, imagem 2 %32
    • Press and slide open the battery cover.

  2. Disassembling Palm Centro Logic Board: passo 2, imagem 1 %32
    • Caution: Turn cell phone off before removing battery!

    • Press battery to the right.

    • Then lift up battery pack to remove.

  3. Disassembling Palm Centro Logic Board: passo 3, imagem 1 %32
    • Phone with battery removed

  4. Disassembling Palm Centro Logic Board, Back Housing: passo 4, imagem 1 %32
    • Remove the touchpad pen from the top left corner on the back to reveal the last of 6 screws to be removed.

  5. Disassembling Palm Centro Logic Board: passo 5, imagem 1 %32
    • Lift the rubber cap at the top right to reveal the sixth screw.

    • Caution: There is a small Palm sticker under the rubber cap. Tampering with or removing this sticker will void your warranty!

    • Remove the six screws using the T5 Torx screwdriver.

  6. Disassembling Palm Centro Logic Board: passo 6, imagem 1 %32 Disassembling Palm Centro Logic Board: passo 6, imagem 2 %32
    • Remove the SIM card so housing can be separated.

  7. Disassembling Palm Centro Logic Board: passo 7, imagem 1 %32 Disassembling Palm Centro Logic Board: passo 7, imagem 2 %32
    • Use a plastic pry tool to separate the bottom of the case to remove the small plastic insert.

  8. Disassembling Palm Centro Logic Board: passo 8, imagem 1 %32 Disassembling Palm Centro Logic Board: passo 8, imagem 2 %32
    • Remove the small plastic insert at the bottom of the phone.

  9. Disassembling Palm Centro Logic Board: passo 9, imagem 1 %32 Disassembling Palm Centro Logic Board: passo 9, imagem 2 %32
    • Continue with plastic pry tool all the way around the phone to remove the back housing.

  10. Disassembling Palm Centro Logic Board, Logic Board: passo 10, imagem 1 %32
    • Carefully peel back the tape holding the speaker (left) and keyboard (right) connection tabs in place.

  11. Disassembling Palm Centro Logic Board: passo 11, imagem 1 %32
    • Using the plastic prying tool, lift the tabs and carefully pull the contact connections out on both sides.

    • Be very careful, these electronics are delicate!

  12. Disassembling Palm Centro Logic Board: passo 12, imagem 1 %32
    • Separate the logic board from the case by lifting and pulling out the bottom.

Conclusão

To reassemble your device, follow these instructions in reverse order.

Uma outra pessoa concluiu este guia.

Equipe

Cal Poly, Team 15-49, Garner Spring 2010 Membro de Cal Poly, Team 15-49, Garner Spring 2010

CPSU-GARNER-S10S15G49

Membros da 5

Autoria de 12 guias

2 comentários

note: if you need to replace the logic board, follow this guide, insert a new board, and then follow the steps in reverse order to get a working phone.

Chelsea Barackman - Responder

i try to on this mobile ..but cant do that, i try to on this mobile so many ways.. i want to whhy thi mobile not on and how to resolve it?

kelumaruna - Responder

Adicione um comentário

Exibir estatísticas:

Últimas 24 horas: 0

Últimos 7 dias: 0

Últimos 30 dias: 4

Duração total: 3,104