Ir para o conteúdo principal

Disassembling Flip Video USB Port

O que você precisa

  1. Disassembling Flip Video USB Port, Outer Shell: passo 1, imagem 1 %32 Disassembling Flip Video USB Port, Outer Shell: passo 1, imagem 2 %32
    • Turn off the device and take the batteries out.

    • Remove metal sticker under the LCD screen with a spudger.

    • This may require a large force to pry off the glued sticker.

  2. Disassembling Flip Video USB Port: passo 2, imagem 1 %32
    • Remove the 4 gray screw caps with the spudger. These cover the screw heads and protect from dirt or grime.

  3. Disassembling Flip Video USB Port: passo 3, imagem 1 %32 Disassembling Flip Video USB Port: passo 3, imagem 2 %32
    • Remove the 5 10mm screws with the #00 Phillips screwdriver. These connect the back of the outer shell to the front of the outer shell.

  4. Disassembling Flip Video USB Port: passo 4, imagem 1 %32
    • Open battery door. This can be done by gently depressing and sliding the battery down downward.

  5. Disassembling Flip Video USB Port: passo 5, imagem 1 %32
    • Use the spudger to separate outer shells.

    • The spudger must be inserted between the shell halves to pry the edges apart.

    • Slowly work around the outside to separate the halves.

  6. Disassembling Flip Video USB Port, Circuit Board: passo 6, imagem 1 %32
    • Remove the 3 5mm screws securing the circuit board to the front shell with the #00 Phillips screwdriver.

  7. Disassembling Flip Video USB Port: passo 7, imagem 1 %32
    • Slowly lift the left side of the circuit board.

    • Do not attempt to remove the circuit board completely yet. It is still connected to the device.

  8. Disassembling Flip Video USB Port: passo 8, imagem 1 %32
    • Disconnect the USB port cable from the back side of the circuit board.

  9. Disassembling Flip Video USB Port: passo 9, imagem 1 %32
    • Slide out the battery contacts.

    • Battery contacts

    • Slot where battery contacts were located

  10. Disassembling Flip Video USB Port, USB Port: passo 10, imagem 1 %32
    • Remove black 3mm screw that secures wire to outer shell with #00 Phillips screwdriver.

  11. Disassembling Flip Video USB Port: passo 11, imagem 1 %32
    • Lift wire out of the outer shell slot.

    • The wire mount should stay attached to the wire.

  12. Disassembling Flip Video USB Port: passo 12, imagem 1 %32
    • Use tweezers to remove the spring that holds the port door shut.

    • Make sure the spring is firmly grasped by the tweezers so that it does not shoot off of the case.

  13. Disassembling Flip Video USB Port: passo 13, imagem 1 %32
    • Remove the 3 screws securing USB port cover to the outer case with the #00 Phillips screwdriver.

  14. Disassembling Flip Video USB Port: passo 14, imagem 1 %32
    • Remove the USB port cover.

  15. Disassembling Flip Video USB Port: passo 15, imagem 1 %32
    • Remove the USB slider.

  16. Disassembling Flip Video USB Port: passo 16, imagem 1 %32
    • Lift out the USB port slowly.

    • Since the hinge is spring loaded, be careful that no pieces fall out when the port is lifted.

Conclusão

To reassemble your device, follow these instructions in reverse order.

Uma outra pessoa concluiu este guia.

Elizabeth

Membro desde: 04/15/10

100 Reputação

Autoria de 6 guias

Equipe

Cal Poly, Team 26-21, Regan Spring 2010 Membro de Cal Poly, Team 26-21, Regan Spring 2010

CPSU-REGAN-S10S26G21

Membros da 4

Autoria de 12 guias

0 comentários

Adicione um comentário

Exibir estatísticas:

Últimas 24 horas: 0

Últimos 7 dias: 0

Últimos 30 dias: 5

Duração total: 4,124