Conserte seus objetos Comunidade Loja

Disassembling Canon PowerShot SD800 IS LCD Display

Introdução

Remove the back cover before removing LCD display.

O que você precisa

  1. Disassembling Canon PowerShot SD800 IS LCD Display, Back Cover: passo 1, imagem 1 %32

    • Remove one 2.25mm screw on the bottom.

    Editar

  2. Disassembling Canon PowerShot SD800 IS LCD Display: passo 2, imagem 1 %32

    • Remove two 2.25mm screws on the right side looking from the front.

    Editar

  3. Disassembling Canon PowerShot SD800 IS LCD Display: passo 3, imagem 1 %32

    • Remove one 4.7mm screw on the side with the AV output.

    Editar

  4. Disassembling Canon PowerShot SD800 IS LCD Display: passo 4, imagem 1 %32

    • Pull off the back cover.

    • The back cover tends to stick in the top corner (near the mode dial) due to a metal clip. Jiggle the cover side to side as you pull it out.

    Editar

  6. Disassembling Canon PowerShot SD800 IS LCD Display, LCD Assembly: passo 5, imagem 1 %32

    • Remove 2 2.4mm screws on bottom.

    Editar

  7. Disassembling Canon PowerShot SD800 IS LCD Display: passo 6, imagem 1 %32

    • Follow the small data cable to where it connects to the camera.

    • Lift the back white portion to unlock the cable.

    • The cable should easily slide out.

    • The connector is very fragile. Use caution when lifting the lock.

    Editar

  8. Disassembling Canon PowerShot SD800 IS LCD Display: passo 7, imagem 1 %32

    • Gently lift LCD display off.

    • There will be two data cables still attached to the camera. Do not break them.

    • There may be a loose strip of metal along the inner side of the LCD display for a secure fit.

    Editar

  9. Disassembling Canon PowerShot SD800 IS LCD Display: passo 8, imagem 1 %32

    • Follow the larger cable to where it connects to the camera.

    • Lift the front black portion of the connector to unlock the data cable.

    • The cable should easily slide out.

    • The connector is very fragile. Use caution when lifting the lock.

    Editar

  10. Disassembling Canon PowerShot SD800 IS LCD Display, LCD Display: passo 9, imagem 1 %32

    • Pry the LCD display out from the four metal clamps.

    Editar

  11. Disassembling Canon PowerShot SD800 IS LCD Display: passo 10, imagem 1 %32

    • To remove the LCD, peel the larger data cable off from the frame.

    • The LCD is glued by its data cable to the back of the LCD frame.

    Editar
Conclusão

To reassemble your device, follow these instructions in reverse order.

Autor(a)

com 3 outros contribuidores

Jeremy Rabaino

Membro desde: 10/10/10

135 Reputação

Autoria de 6 guias

Emblemas: 7

+4 outros emblemas

Equipe

Cal Poly, Team 20-9, Maness Fall 2010 Membro de Cal Poly, Team 20-9, Maness Fall 2010

CPSU-MANESS-F10S20G9

Membros da 5

Autoria de 6 guias

0 comentários

Adicione um comentário

Exibir estatísticas:

Últimas 24 horas: 1

Últimos 7 dias: 1

Últimos 30 dias: 1

Duração total: 2,690