Conserte seus objetos Comunidade Loja

Dexter 900W Corded Hammer Drill - 900ID2.5 Output Shaft Replacement

Introdução

By the end of the guide you will have replaced your output shaft.

O que você precisa

  1. Dexter 900W Corded Hammer Drill - 900ID2.5 Output Shaft Replacement, Unplug: passo 1, imagem 1 %32

    • Before you begin, remember to disconnect the mains plug.

    Traduzir

  2. Dexter 900W Corded Hammer Drill - 900ID2.5 Output Shaft Replacement: passo 2, imagem 1 %32 Dexter 900W Corded Hammer Drill - 900ID2.5 Output Shaft Replacement: passo 2, imagem 2 %32

    • Remove the handle from the machine.

    Traduzir

  3. Dexter 900W Corded Hammer Drill - 900ID2.5 Output Shaft Replacement: passo 3, imagem 1 %32 Dexter 900W Corded Hammer Drill - 900ID2.5 Output Shaft Replacement: passo 3, imagem 2 %32

    • Open the chuck to the maximum to gain access to the inner screw.

    Traduzir

  4. Dexter 900W Corded Hammer Drill - 900ID2.5 Output Shaft Replacement: passo 4, imagem 1 %32 Dexter 900W Corded Hammer Drill - 900ID2.5 Output Shaft Replacement: passo 4, imagem 2 %32

    • Lock the chuck using a 15 spanner (thickness 3), then unscrew to the right with a pz3 screwdriver.

    Traduzir

    • Using a pair of pliers, unscrew the chuck.

    Traduzir

  7. Dexter 900W Corded Hammer Drill - 900ID2.5 Output Shaft Replacement: passo 6, imagem 1 %32 Dexter 900W Corded Hammer Drill - 900ID2.5 Output Shaft Replacement: passo 6, imagem 2 %32

    • Using a screwdriver or screwdriver, unscrew and open the device.

    Traduzir

  8. Dexter 900W Corded Hammer Drill - 900ID2.5 Output Shaft Replacement: passo 7, imagem 1 %32

    • Unscrew the four screws.

    Traduzir

    • Using a screwdriver, lift the spring of the two brushes.

    Traduzir

    • Remove the output shaft.

    • Before replacing the new part, be sure to re-grease.

    Traduzir

    • Reposition the brush springs.

    Traduzir

  12. Dexter 900W Corded Hammer Drill - 900ID2.5 Output Shaft Replacement: passo 11, imagem 1 %32

    • Then retighten the four screws.

    Traduzir

  13. Dexter 900W Corded Hammer Drill - 900ID2.5 Output Shaft Replacement: passo 12, imagem 1 %32 Dexter 900W Corded Hammer Drill - 900ID2.5 Output Shaft Replacement: passo 12, imagem 2 %32

    • Before closing, check that no cable is blocked and that each part is in its place.

    • Tighten the screws to close the device.

    Traduzir

  14. Dexter 900W Corded Hammer Drill - 900ID2.5 Output Shaft Replacement: passo 13, imagem 1 %32

    • Replace the chuck.

    Traduzir

  15. Dexter 900W Corded Hammer Drill - 900ID2.5 Output Shaft Replacement: passo 14, imagem 1 %32 Dexter 900W Corded Hammer Drill - 900ID2.5 Output Shaft Replacement: passo 14, imagem 2 %32

    • Screw the chuck back on by hand.

    • Then using a screwdriver replace the screw, and screw to the left.

    Traduzir

  16. Dexter 900W Corded Hammer Drill - 900ID2.5 Output Shaft Replacement: passo 15, imagem 1 %32 Dexter 900W Corded Hammer Drill - 900ID2.5 Output Shaft Replacement: passo 15, imagem 2 %32

    • Finally replace the handle.

    Traduzir
Conclusão

in order to reassemble preform the steps in reverse order.

Um agradecimento especial a esses tradutores:

fr en

100%

HelloMacOS

HelloMacOS está nos ajudando a consertar o mundo! Quer contribuir?
Comece a traduzir ›

Autor(a)

com 1 outro contribuidor

Céline Chemineau

Membro desde: 01/29/20

16.581 Reputação

Autoria de 95 guias

Emblemas: 12

+9 outros emblemas

Equipe

Leroy Merlin Membro de Leroy Merlin

Community

Membros da 36

Autoria de 239 guias

0 comentários

Adicione um comentário

Exibir estatísticas:

Últimas 24 horas: 0

Últimos 7 dias: 7

Últimos 30 dias: 19

Duração total: 935