Ir para o conteúdo principal

Conserte seus objetos

Direito de executar reparos

Loja

  1. Este passo não foi traduzido. Ajude a traduzi-lo

    Remove the eight 4 mm T5 Torx screws from the bottom cover. Remove the eight 4 mm T5 Torx screws from the bottom cover.
    • Remove the eight 4 mm T5 Torx screws from the bottom cover.

    Missing a step about removing the tiny Phillips head screw under the XPS flip up cover in the middle. Also, there are hooks all the way around the cover so it doesn’t simply lift off.

    curtis_p_brown - Responder

    What about step 3???

    Peter Hecht -

    Please dont hurry , take your Time to follow this procedure. It takes 20 min (not 5) and step 4 requires half of this Time. Good luck.

    Peter Hecht - Responder

    +1 Peter Hecht is right - getting the little clips the back is snapped on with is time consuming and a bit fiddly for people not used to “spudging” off covers. Starting from the back is the key those come loose much easier and help with the rest

    Doug Steinschneider - Responder

  2. Este passo não foi traduzido. Ajude a traduzi-lo

    Use a plastic opening tool to pry open the 'XPS' flap in the middle. Use a plastic opening tool to pry open the 'XPS' flap in the middle.
    • Use a plastic opening tool to pry open the 'XPS' flap in the middle.

    No flap or screw on the XPS 9370, just a press-fit latch at the centre of the cover. This can be gently prised off.

    Alan Thomas - Responder

  3. Este passo não foi traduzido. Ajude a traduzi-lo

    Remove the single Phillips screw hidden beneath the flap.
    • Remove the single Phillips screw hidden beneath the flap.

  4. Este passo não foi traduzido. Ajude a traduzi-lo

    Use opening picks or a plastic pry tool to pry open the case clips, beginning from the back edge.
    • Use opening picks or a plastic pry tool to pry open the case clips, beginning from the back edge.

    It’s not that easy to lift actually, cause there are latches. Had t release them gently all around beforehand.

    Davit Barbakadze - Responder

    Also there’s one additional screw under that plate on the bottom!

    Davit Barbakadze - Responder

    Maybe the later models are different, since it should be from the front: https://www.youtube.com/watch?v=xFIE2SKs...

    shigmas - Responder

    Very difficult step, Proceed very carefull

    Peter Hecht - Responder

    If you are replacing the battery of a 9360 or latter (2016 onward) make sure to do the FRONT first. There are latches on the back that you may break if you try to force it open that way. After prying up the front and the sides, just lift up the front like you would open a hinged box. You shouldn’t feel that much resistance as the back hinges off towards you after you’ve lifted it around 30-40 degrees.

    Giacomo P - Responder

  5. Este passo não foi traduzido. Ajude a traduzi-lo

    Remove the bottom cover.
    • Remove the bottom cover.

  6. Este passo não foi traduzido. Ajude a traduzi-lo

    Pull the battery cable connector towards the battery to disconnect it from its socket. If the connector is stubborn, push a little at one side, then the other, to "walk" it out of its socket.
    • Pull the battery cable connector towards the battery to disconnect it from its socket.

    • If the connector is stubborn, push a little at one side, then the other, to "walk" it out of its socket.

    • If you have trouble walking the connector out of the socket, use the point of a spudger to gently push on the connector indent to slide the connector out.

    • Do not pull up.

    • Open the display and press the power button for five seconds to drain any remaining charge from the system.

  7. Este passo não foi traduzido. Ajude a traduzi-lo

    Use tweezers to remove the little white connector by pulling it out and away from its socket. Use tweezers to remove the little white connector by pulling it out and away from its socket. Use tweezers to remove the little white connector by pulling it out and away from its socket.
    • Use tweezers to remove the little white connector by pulling it out and away from its socket.

  8. Este passo não foi traduzido. Ajude a traduzi-lo

    Remove the black standard flat connector by lifting the tab up with your hand. Remove the black standard flat connector by lifting the tab up with your hand.
    • Remove the black standard flat connector by lifting the tab up with your hand.

    My XPS 13 had a little silver plate with two Philips head screws over the connector that had to be removed to get to the connector

    David Fradkin - Responder

  9. Este passo não foi traduzido. Ajude a traduzi-lo

    Remove the 4 mm Phillips #0 screw that connects the fan to the motherboard. Remove the 4 mm Phillips #0 screw that connects the fan to the base of the computer.
    • Remove the 4 mm Phillips #0 screw that connects the fan to the motherboard.

    • Remove the 4 mm Phillips #0 screw that connects the fan to the base of the computer.

  10. Este passo não foi traduzido. Ajude a traduzi-lo

    Use your right hand to lift up the larger section of the motherboard, closest to the fan. Use your left hand to pull the fan at a 30-degree angle out from underneath the motherboard.
    • Use your right hand to lift up the larger section of the motherboard, closest to the fan.

    • Use your left hand to pull the fan at a 30-degree angle out from underneath the motherboard.

Linha de Chegada

4 outras pessoas concluíram este guia.

Ella Herrmann

Membro desde: 24/04/2017

1.339 Reputação

3 Guias de autoria

Equipe

Cal Poly, Team S21-G6, Livingston Spring 2017 Membro de Cal Poly, Team S21-G6, Livingston Spring 2017

CPSU-LIVINGSTON-S17S21G6

5 Membros

24 Guias de autoria

Great guide! The two hardest parts were getting the back cover off, and lifting the motherboard to remove the fan. Took me about 30 minutes in total.

John Reeder - Responder

It would be really easier if you remove the battery screws first… there are some steps that were not clear…

Nicolás Jiménez Bautista - Responder

This repair took me about 45 min for a complete novice. “Walking out” the battery connector was only way I could unplug it. There was a retaining bracket overlaying the flat connector (step 8) that I needed to unscrew (2 screws, phillips) before it could be removed. Take care to replace the wire in the wire guides along the fan’s housing prior to reinsertion of the replacement fan. It cannot be done afterwards and the back panel will not be flush. Otherwise, this was an excellent guide and an easy repair.

Scott Freeman - Responder

Adicione um comentário

Exibir estatísticas:

Últimas 24 horas: 4

Últimos 7 dias: 77

Últimos 30 dias: 351

Duração total: 9,427