Introdução

If you're having issues with your monitor, you'll most likely need to replace it. Due to the fact that the monitor is one assembly, if a new issue occurs with your screen you'll need to replace the entire screen.

To replace the monitor, you'll need to disassemble most of the laptop.

Peças

Não são necessárias peças.

Make sure the laptop is off before attempting to remove the battery.
  • Make sure the laptop is off before attempting to remove the battery.

  • Flip over your laptop so that the battery faces you.

Adicionar comentário

Slide each latch away from the battery to unlock it.
  • Slide each latch away from the battery to unlock it.

Adicionar comentário

  • Lift the battery upwards to remove it.

    • Continue holding the latches when removing the battery.

Adicionar comentário

  • Remove one 4.8mm screw with a JIS #00 screwdriver.

  • Remove the optical drive.

Adicionar comentário

  • Remove two 4.8mm screws with a JIS #00 screwdriver.

  • Remove the access panel.

Adicionar comentário

  • Remove three 4.8mm screws from the hard drive with a JIS #00 screwdriver.

  • Slide the hard drive to the left.

  • Slide the hard drive to the right and up.

Adicionar comentário

  • Slide the two clips away from the RAM.

  • Lift the RAM out.

Adicionar comentário

  • A metal spudger can scratch delicate internal parts. Be extra careful when removing the keyboard.

  • Use a metal spudger to loosen the main frame of the keyboard.

    • A metal spudger should be used instead of a plastic one because a plastic one will probably break.

    • Make sure to get the spudger under the entire keyboard and not just under the keys.

Adicionar comentário

  • Slowly lift the keyboard.

  • Lift the locking flap that holds the ribbon cable in place.

    • The white line on this ribbon cable marks the edge of the connection area. To reinstall, insert the cable into the connector up to this line, and then close the locking flap.

  • Remove the keyboard.

Adicionar comentário

  • Remove two 1.6mm screws from beneath the optical drive with a JIS #00 screwdriver.

  • Remove the eight remaining 4.8mm screws from the back of the computer with a JIS #00 screwdriver.

Adicionar comentário

  • Remove the two exposed ribbon cables.

  • Remove the palmrest.

Adicionar comentário

  • Remove the display cable on the top-right of the motherboard.

    • Ensure the cable snakes through the path in the case when putting it back together.

  • Remove the two antennae from Wi-Fi chip.

Adicionar comentário

  • Remove the nine 4.8mm screws from the hinges. There are four on the right and five on the left with a JIS #00 screwdriver.

  • Lift the display assembly away from the base.

Adicionar comentário

  • Unsnap the bezel around the edges.

  • Remove the bezel.

  • During reassembly, make sure the wires are tucked inside the hinges so that they fit around the edges.

Adicionar comentário

  • Remove the one 4.8mm screw from each hinge cover with a JIS #00 screwdriver.

    • Do not over-tighten these screws during reassembly, as the hinge cover is thin and may break.

  • Remove the hinge cover.

Adicionar comentário

  • Remove the five 4.8mm screws from each hinge with a JIS #00 screwdriver.

  • Remove one 4.8mm screw from the top left and the top right of the screen with a JIS #00 screwdriver.

Adicionar comentário

  • Be sure not to damage the display cable when lifting the screen!

  • Slowly lift the screen away from the case assembly.

  • Unplug the display cable from the back of the screen.

  • Make sure there are no cables under the screen during reassembly.

Adicionar comentário

  • Remove the four 3.2mm screws from each rail with a JIS #00 screwdriver.

  • Remove the rails from the screen.

Adicionar comentário

Conclusão

To reassemble your device, follow these instructions in reverse order.

Uma outra pessoa concluiu este guia.

David Callahan

Member since: 19-10-2017

513 reputação

5 Guides authored

Equipe

I was able to do this repair on this exact model of laptop without dismantling the bottom half of the laptop. It’s not hard at all, all you’ve got to do is just separate the bezel from the lid of the laptop and pull it out from behind the base. It saves lots of trouble of dismantling. You can’t replace the hinges this way, though, but you can certainly replace the LCD itself without dismantling the bottom half of the laptop.

Joseph Sctbunio - Responder

Adicionar comentário

Visualizar Estatísticas:

Últimas 24 horas: 2

Últimos 7 dias: 10

Últimos 30 dias: 29

Todo: 233