Ir para o conteúdo principal

Cirago M9030 IDE Connector Replacement

O que você precisa

  1. Cirago M9030 IDE Connector Replacement, Cover: passo 1, imagem 1 %32
    • Use a Phillips #00 screwdriver to unscrew the four 1.1mm long screws on each corner located at the top of the cover.

  2. Cirago M9030 IDE Connector Replacement: passo 2, imagem 1 %32
    • Similar to the last step, flip the cover over and use a Phillips #00 screwdriver to unscrew the four 1.1mm long screws on each corner located at the bottom of the cover.

    • Remove the warranty sticker across the bottom.

  3. Cirago M9030 IDE Connector Replacement: passo 3, imagem 1 %32 Cirago M9030 IDE Connector Replacement: passo 3, imagem 2 %32
    • Gently take the cover apart using your hands separating the top and bottom.

    • The outer shell is expected to easily come apart.

  4. Cirago M9030 IDE Connector Replacement, Hard Drive: passo 4, imagem 1 %32
    • Make sure that the screen of the device is facing down.

  5. Cirago M9030 IDE Connector Replacement: passo 5, imagem 1 %32 Cirago M9030 IDE Connector Replacement: passo 5, imagem 2 %32 Cirago M9030 IDE Connector Replacement: passo 5, imagem 3 %32
    • Using the plastic opening tool, wedge the tool underneath the bottom left edge of the hard drive.

    • Raise the bottom edge of the hard drive 15 degrees up from the device.

  6. Cirago M9030 IDE Connector Replacement: passo 6, imagem 1 %32 Cirago M9030 IDE Connector Replacement: passo 6, imagem 2 %32 Cirago M9030 IDE Connector Replacement: passo 6, imagem 3 %32
    • Place fingers on the IDE connectors gently picking up and sliding the hard drive out from the IDE module.

  7. Cirago M9030 IDE Connector Replacement, IDE Connector: passo 7, imagem 1 %32 Cirago M9030 IDE Connector Replacement, IDE Connector: passo 7, imagem 2 %32
    • Using the Phillips #00 screwdriver, unscrew the two 1.5mm long screws holding the IDE connector to the motherboard located at the top.

  8. Cirago M9030 IDE Connector Replacement: passo 8, imagem 1 %32
    • Using the Phillips #00 screwdriver, unscrew the three 1.5mm long screws on the metal bracket.

  9. Cirago M9030 IDE Connector Replacement: passo 9, imagem 1 %32 Cirago M9030 IDE Connector Replacement: passo 9, imagem 2 %32
    • Using the plastic opening tool, completely lift the metal bracket off of the motherboard.

    • Using the plastic opening tool, completely lift the rubber insulator off of the motherboard.

  10. Cirago M9030 IDE Connector Replacement: passo 10, imagem 1 %32
    • Using the plastic opening tool, completely lift the ribbon off of the motherboard.

  11. Cirago M9030 IDE Connector Replacement: passo 11, imagem 1 %32 Cirago M9030 IDE Connector Replacement: passo 11, imagem 2 %32
    • Completely remove the IDE connector from the device.

    • The audio jack is attached to the IDE connector. Pull at a 45 degree angle from the audio jack.

Conclusão

To reassemble your device, follow these instructions in reverse order.

Uma outra pessoa concluiu este guia.

Ryan Sutardji

Membro desde: 06/29/12

171 Reputação

Autoria de 7 guias

Equipe

Cal Poly, Team 1-4, Regan SU 2012 Membro de Cal Poly, Team 1-4, Regan SU 2012

CPSU-REGAN-SU12S1G4

Membros da 4

Autoria de 7 guias

0 comentários

Adicione um comentário

Exibir estatísticas:

Últimas 24 horas: 0

Últimos 7 dias: 1

Últimos 30 dias: 1

Duração total: 964