Conserte seus objetos

Direito de executar reparos

Loja

Canon Powershot A70 Speaker Replacement

Escrito Por: Laura Greek (e 12 outros contribuidores)
  • Comentários: 0
  • Favoritos: 0
  • Execuções: 1

Dificuldade

Moderado

Passos

12

Tempo necessário

20 minutos

Partes

4

Sinalizadores

4

Needs Better Images

Precisa de melhores imagens

Melhores fotos vão melhorar este guia. Ajude tirando, editando ou enviando novas delas!

Grammar Police

Polícia gramatical

Abrace seu professor de Inglês interior e ajude a melhorar a gramática deste guia!

Bullets!

Balas!

Melhor coordenação com marcas e cor/tipo de balas ajudará a tornar mais claro este guia!

Better Introduction

Melhor Introdução

Melhore este guia, completando ou revendo a sua introdução.

Introdução

This guide will help Canon Powershot A70 owners replace the speakers inside their camera.

  1. Open the battery compartment and remove the batteries.

    • Open the battery compartment and remove the batteries.

    • Remove the two screws that are deep in the battery compartment with a Phillips #00 screwdriver.

    Editar

  2. Open the CF compartment and remove the top screw with a Phillips #00 screwdriver. The panel that holds the shutter button and zoom will come off.

    • Open the CF compartment and remove the top screw with a Phillips #00 screwdriver.

    • The panel that holds the shutter button and zoom will come off.

    • Be careful! There are two small wires connecting the speaker to the body of the camera. These are very delicate so proceed with caution. Do not remove.

    Editar

  3. Unscrew the three small screws on the bottom of the camera with a Phillips #00 screwdriver.

    • Unscrew the three small screws on the bottom of the camera with a Phillips #00 screwdriver.

    • Remove the wrist strap.

    Editar

  4. Remove the screw in the CF compartment with a Phillips #00 screwdriver.

    • Remove the screw in the CF compartment with a Phillips #00 screwdriver.

    Editar

  6. Open the rubber Digital AV Out compartment flap. Pry the battery with the IFIXIT opening tool. Carefully pull out the battery with two fingers.

    • Open the rubber Digital AV Out compartment flap.

    • Pry the battery with the IFIXIT opening tool.

    • Carefully pull out the battery with two fingers.

    • Remove the two screws that are now visible with a Phillips #00 screwdriver.

    Editar

  7. Starting from the bottom, carefully pull the casing off. The casing will now pivot at the top.

    • Starting from the bottom, carefully pull the casing off.

    • The casing will now pivot at the top.

    • There are three catches that hold the back casing to the body.

    • You may have to pull with some force. The rear panel will make a snapping noise when it separates from the body.

    Editar

  8. The interior of the camera should look like this.

    • The interior of the camera should look like this.

    Editar

  9. Remove the two screws at the top of the battery compartment with a Phillips #00 screwdriver.

    • Remove the two screws at the top of the battery compartment with a Phillips #00 screwdriver.

    Editar

  10. With your right thumb, pull back on the tab while using your left hand to pull the face of the camera away from the body. With your right thumb, pull back on the tab while using your left hand to pull the face of the camera away from the body.

    • With your right thumb, pull back on the tab while using your left hand to pull the face of the camera away from the body.

    Editar

  11. Remove the two clearly visible screws from the control dial with a Phillips #00 screwdriver, then remove the dial-- it should come off easily.

    • Remove the two clearly visible screws from the control dial with a Phillips #00 screwdriver, then remove the dial-- it should come off easily.

    Editar

  12. You should be able to see the two small wires connecting the speaker to a small green plug. With tweezers, carefully unplug the wires from the plug. The wire should slide straight out.

    • You should be able to see the two small wires connecting the speaker to a small green plug.

    • With tweezers, carefully unplug the wires from the plug. The wire should slide straight out.

    • Carefully replace the broken speaker/shutter panel with a new one.

    Editar

  13. The removed panel should look like this

    • The removed panel should look like this

    Editar
Conclusão

To reassemble your device, follow these instructions in reverse order.

Uma outra pessoa concluiu este guia.

Autor

com 12 outros contribuidores

Laura Greek

Membro desde: 25/01/2010

19 Reputação

2 Guias de autoria

Emblemas: 7

+4 outros emblemas

Equipe

Cal Poly, Team 14-40, Regan Winter 2010 Membro de Cal Poly, Team 14-40, Regan Winter 2010

CPSU-REGAN-W10S14G40

5 Membros

15 Guias de autoria

0 comentários

Adicionar um comentário

Adicione um comentário

Exibir estatísticas:

Últimas 24 horas: 0

Últimos 7 dias: 2

Últimos 30 dias: 4

Duração total: 2,880