Conserte seus objetos Comunidade Loja

Canon PowerShot SX260 HS Flash Assembly Replacement

O que você precisa

  1. Canon PowerShot SX260 HS Flash Assembly Replacement, Flash Assembly: passo 1, imagem 1 %32 Canon PowerShot SX260 HS Flash Assembly Replacement, Flash Assembly: passo 1, imagem 2 %32 Canon PowerShot SX260 HS Flash Assembly Replacement, Flash Assembly: passo 1, imagem 3 %32

    • Be sure to always remove the battery from the camera before disassembling to avoid permanent damage.

    • The camera has a total of 6 (3 mm) external screws that will need to be removed; 2 on the left side, 2 on the bottom, and 2 on the right side.

    • Remove the 2 screws on the left side.

    • Remove the 2 screws on the bottom of the camera.

    • Remove the 2 screws on the right side of the camera.

    Editar

  2. Canon PowerShot SX260 HS Flash Assembly Replacement: passo 2, imagem 1 %32

    • Use your plastic opening tool to gently lift and remove the back face plate.

    Editar

  3. Canon PowerShot SX260 HS Flash Assembly Replacement: passo 3, imagem 1 %32

    • After removing the exterior screws, use your fingers to gently lift off the front face plate.

    Editar

  4. Canon PowerShot SX260 HS Flash Assembly Replacement: passo 4, imagem 1 %32

    • Next, remove the 2 (3 mm) interior screws on the left side of the camera.

    Editar

  6. Canon PowerShot SX260 HS Flash Assembly Replacement: passo 5, imagem 1 %32

    • After removing the interior left screws, use a plastic opening tool to gently pull the top face plate off.

    Editar

  7. Canon PowerShot SX260 HS Flash Assembly Replacement: passo 6, imagem 1 %32

    • Next, you will need to remove the dial panel by removing the 2 (3mm) screws on the back side of the camera.

    • Gently remove the dial panel with your fingers.

    Editar

  8. Canon PowerShot SX260 HS Flash Assembly Replacement: passo 7, imagem 1 %32 Canon PowerShot SX260 HS Flash Assembly Replacement: passo 7, imagem 2 %32

    • Remove 1 (3 mm) screw from the flash generator with a Phillips screw driver

    • Gently lift the flash generator off of the camera with the plastic opening tool .

    Editar

  9. Canon PowerShot SX260 HS Flash Assembly Replacement: passo 8, imagem 1 %32
    Ferramenta utilizada nesse passo:
    Tweezers
    $4.99
    Comprar

    • Gently unplug the ribbon cable with your tweezers.

    • Be careful not to rip it.

    Editar

  10. Canon PowerShot SX260 HS Flash Assembly Replacement: passo 9, imagem 1 %32 Canon PowerShot SX260 HS Flash Assembly Replacement: passo 9, imagem 2 %32

    • Using your plastic opening tool to gently move the plug lock from the end of the ribbon cord by lifting it upward.

    • Gently remove the ribbon cable from the connector with tweezers.

    Editar

  11. Canon PowerShot SX260 HS Flash Assembly Replacement: passo 10, imagem 1 %32 Canon PowerShot SX260 HS Flash Assembly Replacement: passo 10, imagem 2 %32

    • Gently remove the ribbon cable assembly from the top of the camera with your tweezers.

    • This cable is a long piece that runs across the top of the camera.

    • The flash assembly is connected to this cable.

    • Once removed gently lift out of the camera

    • Replace the ribbon cable with the attached flash assembly.

    Editar
Conclusão

To reassemble your device, follow these instructions in reverse order.

Uma outra pessoa concluiu este guia.

Autor(a)

com 4 outros contribuidores

Tyler Kelch

Membro desde: 03/05/15

622 Reputação

Autoria de 4 guias

Emblemas: 8

+5 outros emblemas

Equipe

Sam Houston State, Team 11-8, Blackburne Winter 2015 Membro de Sam Houston State, Team 11-8, Blackburne Winter 2015

SHSU-BLACKBURNE-W15S11G8

Membros da 2

Autoria de 4 guias

0 comentários

Adicione um comentário

Exibir estatísticas:

Últimas 24 horas: 1

Últimos 7 dias: 10

Últimos 30 dias: 20

Duração total: 1,665